From the diagram shown select from the list on the right which component represents the block labled 'Q'. (enter answer as a-h) Tablets/botle 17 a. Adder 4 bits b. Comparator c. Encoder d. Decoder Register A 2-digit BCD U 00 O2 3 Keypad e. Multiplexer f. Demultiplexer g. Counter h. Register Code converter 8 bits 8 bits BCD to binary V B 8 bits Total tablets bottled 00000 Valve 8 bits CLK 16 bits Sensor W Register B 16-bit binary 000 8 bits CLR Conweyor Z 16 bits Switching sequance control input R → S - 550 Remote unit

Q: 4) Please briefly explain the areas where flip-flops, encoders/decoders, and…

A: Flip-flops are used in digital circuits to store a single bit of information, which can be either a…

Q: Name all six segment registers.

A: Registers: It is a hardware device which is used to store binary data like program counter,…

Q: Construct the state table, and draw the state transition diagram and the time diagram of the…

A:

Q: 12) A circuit in the arithmetic-logic device could be included in the "execute" loop of the…

A: Please see the next step for solution

Q: Count Enable C K J QB

A: The answer is

Q: 1. A flip-flop has ( ) states.(3') 2. The n-bit shift register composed of n JK flip-flops can…

A: 1. A flip flop has two states. A flip flop has two stable states either 0 or 1. It is also known as…

Q: (b) Describe the state diagram below in detail. Hint: This state machine describes the operation of…

A: State diagram:- A state diagram is applied to show the state of the system. It’s a type of…

Q: A- What the mean of De-multiplexers and design 1 to 4 channel De- multiplexers. B- Implementations…

A: What the mean of De-multiplexers and design 1 to 4 channel De-multiplexers. The data distributor,…

Q: State and explain the methods used to narrow the logic-memory gap. The answer should not be less…

A: Methods used to narrow the logic-memory gap are explained below. I have given you 4 as mentioned in…

Q: Using a. & b. design FSM for 3-bit shift register and simulate it using C, that can

A: #include<stdio.h> #include<conio.h> #include<process.h> int nand(int input1, int…

Q: Design an encoder for coding 4 inputs and 2 outputs (Encoder 4x 2) ?

A: As per guidelines I can answer only first question. I hope you will understand. Thank You.

Q: 5. A four-bit binary counter contains the number 0100. Nine input pulses occur. The new counter…

A: question number 5)    Introduction The explanation is as follows. Explanation A 4 bit…

Q: ) Design a synchronous counter by taking account the following counting order;…

A: Answer is given below

Q: benefits of implementing combinational logic using ROM devices

A: The question wants to know benefits of implementing combinational logic using ROM devices.

Q: (b) Describe the state diagram below in detail. Hint: This state machine describes the operation of…

A: The educational objective of this laboratory is to investigate the creation of custom IP to…

Q: Construct a logic circuit on the ROM that produces the outputs given in the table below by comparing…

A: Lets see the solution.

Q: Step 8 – In the space below, draw the state diagram for the 8-bit counter if the upper nibble enable…

A: 8-bit up/down counters feature internal-carry look-ahead circuitry for cascading in high-speed…

Q: (B) If you have four registers, the size of each one is 8-Bits, and we want to design a simple Bus-…

A: If you have four registers, the size of each one is 8-Bits, and we want to design a simple…

Q: a) Express the number (+62)a as an 8-bit 2's complement form. b) Add the following BCD numbers:…

A:

Q: How to use Flip Flops to design a five bits Serial in /parallel out shift register ? Explain with…

A:

Q: 2. Use state machine to design a binary up/down counter that counts from 0 through 12.

A: Counter is as type of special sequential circuits that repeatedly sequence through a set of…

Q: Design a digital logic circuit as a Read Only Memory (ROM) [Decoder plus OR gates]. A ROM accepts a…

A: This question is from the subject computer organization where we have to draw a ROM as per the given…

Q: diagra escribes operation of a servo motor (scans three angles 0°, ± 90º) based on the pushbutton…

A: what is servo motor? The servo motor is used for servo system. The servo system is a control system…

Q: The term LAB stands for(a) logic AND block (b) logic array block(c) last asserted bit (d) logic…

A: The term LAB stands for

Q: Draw a diagram showing how one flip-flop in the MIPS register file connects to the three ports.…

A: The following block diagram shows a register connected to three different ports. Also decoder and…

Q: QI) Answer two of the following: A) List all categories and sub-categories of Programmable Logic…

A: Q1) A) Answer: categories and sub-categories Programmable Logic Devices (PLDs) Logic:…

Q: H. Flip flops and registers Moodle question 23 Clock Clear DI Clock D2- Select Clear Select -) For…

A: Explanation is given in the below images. See below steps.

Q: H. Flip flops and registers Moodle question 23 Clock Clear DI Clock D2- Select Clear Select b) For…

A: I am giving you detailed explanation in the below handwritten images. See below steps.

Q: 1. Design Procedure 2. Adders and Subtracter 3. Code Conversion 4. Decoders and Encoder

A: Answer1 Design Procedure: design procedure follow 6 steps. 1. Characterize the Problem  You cannot…

Q: Q1/Give the operation (function) for every section: 1.ALU 2.EFI in (8284A) IC 3.RISC 4. program…

A: ANSWER: 1. ALU

Q: 1- Design an encoder for coding 4 inputs and 2 outputs (Encoder 4x 2) ? 2- Design with drawing an…

A: 1. Designing an encoder for coding 4 inputs and 2 outputs An Encoder is a combinational circuit that…

Q: For the diagram shown and list included select which item in the list represents area O.(enter…

A: Please find the solution below in second step:-

Q: Design a binary counter with D Flip-Flops that goes through the following repeated sequence:…

A: Question from sequential circuit, in this we have a Binary counter with D flip flops. In D flip…

Q: a Ports of the 8051 Microcontroller are characterized as All require pull-up resistors between port…

A: Option A All the require pull up resistors between port and load

Q: Question a) Construct a circuit with the help of two serial registers which can swap the contacts…

A: Solution:--    1)As per given in the question is to provide the solution for the     constructing of…