From the beam shown, fc' = 28 MPa, fy = 414 MPa, βh = 1.20, Cc = 40 mm. Take D = 25 mm diameter size. c) Determine the width of the crack.

Q: The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment…

A:

Q: analyze the frame shown. -lin at cu

A: Given: AB = 4m           BD= 4m           BC= 3m           Lateral point load at D = 30 kN…

Q: The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment…

A:

Q: A 2 in. diameter puncher is used to punch a hole through a steel plate 1/2 in. thick. The force…

A: Given data, Force P = 45000 lb = 45 kip Diameter of hole D = 2 inch Plate thickness t = 0.5 inch To…

Q: A kinked edge crack has been detected in a large plate which is to be loaded by a remote tensile…

A: I have solved your problem

Q: Please analyse question 3C(i) with a M1 = 35kN.m as an un-cracked section and 3C(ii) with a M2 =…

A: Given data  Es = 200 GPA  Ec = 30 GPA b = 300 mm  h = 520 mm  d = 460 mm  m = 6.67  As = 1470 mm2

Q: The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment…

A:

Q: Using the method of consistent deformations, calculate the support reactions and draw shear force…

A:

Q: The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment…

A: Outer diameter of aluminum shaft, Wall thickness of aluminum shaft, Outer diameter of steel shaft,…

Q: area of the triangle s

A: A triangle is a 3 sided geometric figure . Area of the triangle with three different sides is given…

Q: The stress intensity factor for a partial-through thickness crack is given by where a is the length…

A: Schematic diagram of the given problem as per the statement: Factor toughness (k) = 30 Mpa m1/2…

Q: The sections of a simply supported beam are shown in Fig. a. Check if the bar arrangement satisfies…

A:

Q: The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment…

A:

Q: A thin walled rotating shaft is subjected to a torque and a bending load. The torque produces the…

A:

Q: Prob. 6.8-10. Using the shear-stress formula, Eq. 6.67, deter- mine an expression for the shear…

A: Given data:- The free body diagram of the shear stress at the neutral axis level on the circular bar…

Q: 9.6 Determine the stresses in the two segments of the bar shown. Segment A has a diameter of 1 in.…

A: FOR SEGMENT A DIA = 1.25 IN. LOAD= 10 KIP FOR SEGMENT B CROSS SECTION = 2IN * 2IN LOAD =22 KIP

Q: Calculate the stress from a 0.3498 in. diameter tensile specimen yielding at 4.407 kips 46.0 ksi…

A:

Q: 9. (a) Sketch the Mode I, Mode II, and Mode III crack opening geometries, and clearly state which is…

A: Note : As per guidelines, we will only discuss the first one as it is not particularly mentioned…

Q: -gment (1) is a tube with an outside diameter of D- ear modulus of G₁ = 4,000 ksi. Steel segment (2)…

A:

Q: Calculate the internal torques T₁ and T₂ in shaft segments (1) and (2), respectively. On paper,…

A: Determine the internal torque of shaft 1 and 2 and draw internal torque diagram.

Q: = The compound shaft shown consists of aluminum segment (1) and steel segment (2). Aluminum segment…

A:

Crack Detection

Concrete materials are meant for supporting structures, building foundations and they act as several load-bearing structures. Over time, due to environmental conditions, and based on the constituent materials used, concrete materials are subjected to a great degree of distress. Corrosion of the reinforcement bars due to chemical influences, uneven base, earthquake, drying shrinkages, and alkali-aggregate reactions are some of the reasons for concrete distress.