Answered: friction factor

Name: Water passed at the same velocity through two pipes of the same length
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Water passed at the same velocity through two pipes of the same length and diameter. The friction factor for a rough pipe is f1 and that for a smooth pipe is f2. Pick out the wrong statement.a. f1 > f2b. None of thesec. Insufficient datad. f1 = f2

Engineering

Mechanical Engineering

friction factor

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 17RQ: Convert 22C to Fahrenheit.

See similar textbooks

Similar questions

Q1/ Explain the pressure loss in the four- section petroleum well drilling system 1. Surface connections. 2. Pipes including drillpipe, heavy walled drillpipe and drill collars. 3. Annular areas around drillpipes, drillcollars, etc. 4. Drillbit. Note: The explanation is in text format, with the equations and drawings, if any, mentioned
Three types of fluids stack in an open tank as shown in the plot. Select the expression of the gage pressure at location 2, P2(gage)=______ A. B. C. D. patm
Write T as an answer if the statement is true and F as an answer if the statement is wrong. If your answer is F, then correct the statement Example: Q1- Sinop is a southern city located at Anatolia. A typical answer 1- F: Sinop is a northern city located at Anatolia. Question2-1 Thermal hot wire anemometers measure the temperature of the flow, and they are very small devices which do not disturb the flow significantly. Question2-2 Using a Laser Doppler velocimetry, one can measure the velocity information at a cross section instantaneously. Question2-3 An obstruction flow meter can be used to measure the velocity profile around a car in a wind tunnel. Question2-4 The exact value of the discharge parameter of an orifice meter should be supplied by the producer because it has a design based value.
Velocity squared divided by double gravity is called the velocity head. If the mass entering a tank is greater than the mass exiting the tank, then the amount of mass in the tank will decrease through time. A flow in a pipe that has a Reynolds number of 105 would be considered a T F T F T F turbulent. d. T F The partial derivative of velocity with respect to time is called the convective acceleration. F The center of pressure is never above the centroid of a planar surface. An object submerged in oil (S = 0.88) will have a smaller buoyant force acting on it than when it is submerged in water. Turbulent flow in pipes tends to have a more uniform mean velocity profile than laminar flow in pipes. The Bernoulli equation requires that the two points in question are on the same streamline. e T F F h F i The weight of an object is different under water than it is out of the water. A pathline traces all particles that pass through a given point through time. F T F
35 + 9.81 (0.3824 - 7-2) = - 49.54 kPa. S. Chand Je oadall i.e.p =- 49.54 kPa. This shows that the given pressure at A, 35 kPa is gauge pressure and hence there is vacuum at point B. (Ans.) Example 6.5. An open circuit wind tunnel draws in air from the atmosphere through a well contoured nozzle. In the test section, where the flow is straight and nearly uniform, a static pressure tap is drilled into the tunnel wall. A manometer connected to the tap shows that the static pressure within the tunnel is 45 mm of water below atmosphere. Assume that air is incompressible and at pressure is 100 kPa (absolute). Calculate the velocity in the wind tunnel section (Refer to Fig. 6.6). Density of P.- 100 kPa water is 999 kg/m' and characteristic gas constant for V =0 air is 287 J/kg K. ساP حقوق النشر Test section 25°C. = 25°C (GATE)
Can i get help with these questions
1. Write the given data and the required quantity.2. Write the formula and solve for the required quantity.3. Encircle or box the final answer.4. Draw a clear diagram of the pipe system that indicates the following: (a-1) water flow reflecting the quantities involved in describing fluid flow and (a-2) the quantities that describe Bernoulli’s equation.5. Write the Bernoulli’s Equation using subscripts U ad L for the upper and lower points respectively. Then determine the pressure at point B?
A pump is working on these parameters 0.56 me/s with TDH of 63 meters. The pump efficiency is at 0.94% and the motor efficiency is at 0,89 %. What is the brake power in kW? Make your answer in whole number and choose the next whole number, say for example 25.2 kW it should be 26 kW.
please help me answer this question with complete solution and figure. i promise to give high rating, thank you very much.
35 + 9.81 (0.3824 - 7-2) = - 49.54 kPa. S. Chand e oladall i.e.Pg =- 49.54 kPa. This shows that the given pressure at A, 35 kPa is gauge pressure and hence there is vacuum at point B. (Ans.) Example 6.5. An open circuit wind tunnel draws in air from the atmosphere through a well contoured nozzle. In the test section, where the flow is straight and nearly uniform, a static pressure tap is drilled into the tunnel wall. A manometer connected to the tap shows that the static pressure within the tunnel is 45 mm of water below atmosphere. Assume that air is incompressible and at pressure is 100 kPa (absolute). Calculate the velocity in the wind tunnel section (Refer to Fig. 6.6). Density of P.= 100 kPa water is 999 kg/m' and characteristic gas constant for V =0 air is 287 J/kg K. ساP حقوق النشر 25°C, Test section = 25°C (GATE)
The ratio of entry diameter with exit diameter is 0.4 in a control volume of pipe segment. What is the corresponding ratio of entry to exit velocity? Recall Q1=Q2 and v1A1=v2A2 Correct answer has a margin of 0.1 from exact answer.
Learning Portal Academic Departments ETC - CIMS - Courses - Reports - e-Services - Moham Select one: O True O False The energy loss due to the change of flowrate of a fluid flow in direction is known as minor loss. Select one: O True O False Determine the time taken by the oil to get collected in a measuring jar of 26 x 10-3 m³. The oil has the specific that has a mean velocity of 9 m/s in a pipe of cross-sectional area 11 x 10-5 m2. Time taken (in s) arch EUROSTARD