Fresh apple juice contains 75% water flowing at a mass flow rate of 200 kg/h. The fresh juice is concentrated in an evaporation process. A portion of the fresh feed is bypassed to meet the evaporator maxi- mum capacity. The bypass stream joins the evaporator outlet stream. Ninety percent of the water entering the evaporator is evaporated. The concentrated apple juice contains 25% water. Draw the process flow sheet and calculate the mass flow rates of nroduced and evaporated streams. (66.7. 133.3 kg/h)

Q: X(s)- G₁(s) G₂(s) Gy(s) G,(s) G4(s) Gg(s) Go(s) Gg(s) Go(s)

A: Given block diagram is

Q: Derive Laplace transforms of the input signals shown in Figs. by summing component functions

A:

Q: Q2 prove that the following flow chare depicts a balanced process by writing thae balances: o-8 ibm…

A: Given: In Feed, Total mass F = 10 lbm, mass fraction of H2 = 0.5 and mass fraction of O2 = 0.5 Top…

Q: The time required for the response to reach 50% of its final value for the 1st Delay Time Peak Rise…

A: Dear subscriber! As per your indication for us to answer only 9 and 10, please note that the…

Q: 49 Q7. A system transfer function is given as G(s): (s+8)' It is subjected to a unit step input,…

A:

Q: Q3/A) Is the response for the following system is under damping? If yes, determine the maximum over…

A: Step 1:

Q: Find the transfer functions C(s)/R(s) and C(s)/D(s) for the system given below.

A:

Q: Reactor coolant system (RCS) hot leg temperature is 568 deg F and RCS pressure is decreasing due to…

A: To find:The pressure range includes the pressure at which two-phase flow will first occur in the hot…

Q: Q2. Find the closed loop transfer function of the system given below. C(s) R(s) 1 (s + 1)3

A:

Q: G₂ (s) 50 ; Gr(s) = 30s + 1' 1 10s +1 ; G₁(s) = 0.016 3s +1

A: Given,

Q: ven the step input 8/s and a second order transfer function model shown below, what is the maximum…

A: Given Data : The step input value =8sThe second order transfer function is given as  G(S) =…

Q: The design team responsible for developing this product attempt to study the passage of raw corn…

A: (1) The time taken by popcorn to travel from one end to other end of the reactor at a heating rate…

Q: 1 The system transfer function is G(s) = then the time [s+0.2] response to a step input will be O a.…

A:

Q: In dynamic state the variables with respect to time. O stay constant

A: "Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A pneumatic controller is used to control temperature within the range 280 K to 310 K. The…

A: Given information:   The temperature range of the controller is 280 K – 310 K Initial output…

Q: The design flow rate is 0.5m³/s. A deep bed monomedia filter with a design loading rate of 500…

A: Given that- Design flow rate, Q=0.5 m3/s Design loading rate, q=500 m3/d.m2 Surface area of filter…

Q: What is the transfer function for the process

A: The relationship between input variable and output variable of a process as a function of time is…

Q: X (s) Gy(s) G₂ (s) G₂(s) G5(s) Gg(s) G₂ (s)

A:

Q: What is the maximum number of independent balances that may be written around each subsystem?…

A:

Q: Create an RC circuit (DC supply 10V) that has a RC time constant equal to conds. Pick the resistor…

A: Problem 7: An RC circuit with an input voltage of 10V and time constant of 3.3sec is created using…

Q: X(s)- G₁(s) G₂ (s) G3(s) G4(s) G5(s) Ge(s) Y(s)

A: Given block diagram is

Q: Draw a Process and Instrumentation Diagram (P&ID) for Continuous stirred tank reactor (CSTR) with…

A: Here , there is a CSTR with assume exothermic reaction and for temperature controll we're using…

Q: The time constant and the steady-state gain for the following transfer function (G(s)=1/(s+0.25))…

A: General general first order transfer function is given as below:         G(s) = G(s)/ R(s)…

Q: Q 3. A single tank process is operating for a long period of time and the inlet flow rate q; is 30.4…

A: single tank process inlet flow rate qi=30.4 ft3/min on increasing flow rate by 10% there is change…

Q: Q2: Consider the following control system 2 Ke (1 + Tos) For K. = 2, tD = 1 and step change in load…

A:

Q: 1. Calculate the flow of liquid solution through the valve in Ib/h. the valve capacity factor is 100…

A: The flow of liquid solution through the valve is to be determined.

Q: During the phase transition the ....or... of .change abruptly. the volumetric or specific values of…

A: The answer is based on the Chemical Engineering Thermodynamics principles.

Q: 1. What are the main components of closed conduits flow networks?

A: Introduction: Fluid flow: Fluid flow is usually the movement of fluid this is subjected to distinct…

Q: Q2: Draw Process Flow Diagram for the following block diagram and Suggest control loop systems for…

A: A control system is defined as a system of devices that manages, commands, directs, or regulates the…

Q: Derive the transfer function for the process below from the generic equation in the image below:

A:

Q: Area A₁ ?In fig. if D1= 4 cm,V1= 10 m/s, Q 0 -Control volume (CV)- Fluid element of velocity v =B…

A: Given, D1 = 4 cm V1 = 10 m/s

Q: 129. A control system has the following transfer function 7(s)=(8-1) (+1) s(8-2)(8+4) The initial…

A: Given               f(s) = ((s-1)(s+1))/(s(s-2)(s+4))

Q: A.No.3: Briefly explain with flow diagram ,the manufacturing process of any one of the basic…

A: Refractory materials are compounds that are used as an insulating material or high temperature…

Q: Give at least 3 examples of under the Chemical Engineering Field that uses numerical analysis.…

A: To give 3 examples under the Chemical Engineering Field that uses numerical analysis which Includes…

Q: Y (s) 3e-0.5s X(s) 5s + 0.2 n the steady-state gain, time constant, and dead time of this process.

A: A certain process describe by following equation Find Study state gain Time constant Dead time

Q: Can a tank with the outflow rate fixed by a constant speedpump reach a steady state if the inlet…

A: It is to be mentioned whether or not a tank with a fixed outflow rate by a constant speed pump can…

Q: A) In an attempt to make the membrane process more time efficient, you want to operate the same…

A: A)At a higher flowrate we need the membrane process more time efficient Find-Set of experiments to…

Q: Q.5 Analyze the degree of freedom or how many independent controllers to be incorporated for the…

A:

Q: Ôn the basis of stability how many 4 3 1 6 parts can the s-plane are divided? The type of an open…

A:

Q: Explain the closed and open loop type of controls systems with example.

A: 1. Closed-Loop Control SystemsClosed-loop control systems, also known as feedback control systems,…

Q: 2- Find the Re number for a fluid with the following properties. Based on the Re number the fluid is…

A:

Q: 2. For the control system shown in Fig. (2), determine: a) C(s)/R(s) b) C(0.5) and C(∞) c) Offset U…

A: Following subparts for the given closed loop are to answered.

Q: Q4- Answer the following 1- Poles with the same dumping ratio lie a- On the same distance from the…

A: Hello Subscriber! There are multiple questions posted. As per our policy, we have solved the first…

Q: What is the steady state output of the given transfer function. (s +1)(s +2)

A:

Q: The time constant and the steady-state gain for the following transfer function (G(s)=1/(4s+1)) will…

A: The time constant and steady-state gain for the given transfer function is to be determined.

Q: them

A: Use and Installation Location of Flow Meter

Q: A tank used to correct for fluid flow rate fluctuations is known to exhibit a second order dynamic…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…