Four resistors, R1 = 100 N, R2 = 250 N, R3 = 350 n and R4 = 200 N are connected such that the parallel combination of R, and R2 is connected in series with the parallel combination of R3 and R4. The series-parallel combination is then connected across a 24 V DC power supply. A. Draw the schematic diagram and label the circuit elements. B. Calculate the equivalent resistance of the circuit. C. Find the total current of the circuit, the voltage across each resistor and the current through each resistor.

Four resistors, R1 = 100 N, R2 = 250 N, R3 = 350 n and R4 = 200 N are connected such that the parallel combination of R, and R2 is connected in series with the parallel combination of R3 and R4. The series-parallel combination is then connected across a 24 V DC power supply. A. Draw the schematic diagram and label the circuit elements. B. Calculate the equivalent resistance of the circuit. C. Find the total current of the circuit, the voltage across each resistor and the current through each resistor.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The average value of the alternating voltage between the ends of a resistor is 12.12V and its frequency is 50 Hz.a. Write the mathematical expression for the voltage.b. Calculate the effective voltage value.c. Find the instantaneous value of the voltage 12 ms after zero.
Q2/ for the series circuit in the Figure beside a. Find the total resistance.. b. Calculate the source current Is. c. Determine the voltages V1, V2, and V3. d. Calculate the power dissipated by R1, R2, and R3. e. Determine the power delivered by the source, and compare it to the sum of the power levels of part (d). 20 V R₁=20 R₂ = 50 W +
Consider the series and parallel resistance circuit below. a. Calculate the total equivalent resistance for the circuit. b. calculate the magnitude of the total circuit current, and the current flow through each 4 Ohm resistor. c. calculate the magnitude of the voltage drops across each circuit element.
Which statements are true? a) At any junction point in a circuit, the sum of all the currents entering the junction must equal the sum of all the currents leaving the junction. b) The sum of the changes in potential around any closed loop of a circuit must equal zero. c) Kirchoff's junction rule is based on the conservation of energy. d) Kirchoff's loop rule is based on the conservation of charge.
Why do power lines near your home contain transformers? A Transformers increase the current flowing into your home. B The transformers reduce the voltage to a level the wires in your house can safely carry. C The transformers increase the voltage supplied to your home during peak usage times. D Transformers decrease resistance in the power lines.
2. Consider the circuit shown in Figure 2. Given V₂ Determine the values of R₁, R₂ and R₁. i₁ R₁ ww + V2 R₂ Figure 2 2 50 Ω ww RA
What is the total power delivered by the 16-volt battery in the circuit below? V1 = 16 volts, V2 = 20 volts, R1 = 7.0 Ω, R2 = 3.0 Ω, and R3 = 2.0 Ω, a. 24 watts b. 36 watts c. 48 watts d. 60 watts e. 12 watts
7. You want to reduce your carbon footprint in the next Yuletide season, so you plan to re-use last year's Christmas lights to your Christmas tree. You notice that one of the lightbulbs stops working but the other remaining bulbs are still in good condition. What is your hypothesis regarding how these lightbulbs are connected? Group of answer choices The lights are connected in a series circuit. The lights are connected in a parallel circuit. It would be impossible to determine the type of connection for the lights without dismantling the wiring. The lights are connected in a combination of series and parallel circuits.
Fill in the blanks in the table.
13. You've designed a schematic symbol for a collection of specialty limit switches required for a control circuit. What tool in AutoCAD Electrical can you use to detect errors related to the layers of the drawing and the orientation of the symbol? A. Required Rollout B. Symbol Audit C. Wblock Editor D. Properties 14. What block file format must be available in a drawing to add panel components? A. DWG B. WD PNLM C. MDB D. WD M 15. Two design engineers are discussing AutoCAD Electrical software. Engineer A says that Project Description reference files use a .wdd extension. Engineer B says that the reference files supported by AutoCAD Electrical are ASCII text files with different file extensions. Who is correct? A. Both Engineer A and Engineer B are correct. B. Only Engineer A is correct. C. Only Engineer B is correct. D. Neither Engineer A nor Engineer B is correct.
7. In a DC circuit 8.41 x 10 19 electrons travel through a point in the circuit in two seconds. What current is in the circuit? a. 7.43 Amperes b. 5.36 Amperes c. 6.73 Amperes d. 1.10 Amperes e. 8.41 x 1019 Amperes
Based on the circuit shown below, according to Kirchoff’s current rule, thecurrent in point b is equal to the current in a. point cb. point dc. point c+dd. indeterminate Based on the circuit shown below, according to Kirchoff’s current rule, the emf inthe battery is equal to the potential difference measured between a. points a and bb. points b and cc. points c and dd. points a and d