Four gears are attached to a circular shaft and transmit the torques shown in the figure. The allowable shear stress in the shaft is 10000 psi8000 lb-in.19,000 lb-in.4000 lb-in.A7000 lb-in.BD(a) What is the required diameter d of the shaft (in inches) if it has a solid cross section?in.(b) What is the required outside diameter d (in inches) if the shaft is hollow with an inside diameter of 1.4 in.?in.

Data given Allowable shear stresses = 10000 psi b) inside diameter = 1.4 in

Four gears are attached to a circular shaft and transmit the torques shown in the figure. The allowable shear stress in the shaft is 10000 psi 8000 lb-in. 19,000 lb-in. 4000 lb-in. A 7000 lb-in. B (a) What is the required diameter d of the shaft (in inches) if it has a solid cross section? in. (b) What is the required outside diameter d (in inches) if the shaft is hollow with an inside diameter of 1.4 in.? in.

Four gears are attached to a circular shaft and transmit the torques shown in the figure. The allowable shear stress in the shaft is 10000 psi 8000 lb-in. 19,000 lb-in. 4000 lb-in. A 7000 lb-in. B (a) What is the required diameter d of the shaft (in inches) if it has a solid cross section? in. (b) What is the required outside diameter d (in inches) if the shaft is hollow with an inside diameter of 1.4 in.? in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The splined ends and gears attached to the steel shaft are subjected to the torques shown in Figure 4. Take G = 75 GN/m². (i) (ii) Determine the location along the 40 mm diameter shaft where the shear stress is largest and plot the variation in shear stress from the shaft centre to its outer surface. Determine the angle of twist of sections C, D, and B relative to end A by producing a graphical plot of the variation of angle of twist from end A to end B (wind-up diagram). 300 N-m 500 N-m A www. 300 mm 200 N.m MAAN 400 mm Figure 4 500 mm 400 N-m
Gear shaft ABCDE is subjected to the torques shown in the figure. Find the internal torque in each seg- ment, and then plot the torsional moment diagram. Assume that the spacing between gears is constant, i.e., 10 in. T1 = T2 = 1000 lb-in. 500 lb-in. A B T3 = 800 Ib-in. C Ta = 500 lb-in. d = 1.0 in. D T; = 800 lb-in. E
Question (1): A stepped shaft ABCD consisting of solid circular segments is subjected to three torques, as shown in the figure. The torques have magnitudes 12.5 kips. in., 9.8 kips, in., and 9.2 kips. in. The length of each segment is 25 in. and the diameters of the segments are 3.5 in., 2.75 in., and 2.5 in. The material is steel with shear modulus of elasticity G = 11.6 x 103 ksi.(a) Calculate the maximum shear stress Tmax in the shaft. (b) Calculate the angle of twist (pp (in degrees) at end D. 13.5 in. 12.5 k-in. -25 in.- B 9,8 k-in. 12.75 in. -25 in.- 9.2 k-in. 12.5 in. c t -25 in.-
TORSION An aluminum shaft with a constant diameter of 70 mm is loaded by torques applied to gears attached to it. Use G = 28 GPa. DETERMINE: A. the relative angle of twist of gear D relative to gear A (in degrees) B. the direction of the rotation of A relative to D? PROVIDE FBD
The two solid steel shafts shown in the figure are connected together using gear wheels. The length of the CD shaft is Lcd=2 m and the length of the AB shaft is LAB= 1.5 m. The radius of gear C is rc=45 mm and the radius of gear B is rB= 90 mm. The CD and AB shafts rotate freely in the bearings on which they are supported. Also, shaft AB is fixed at point A. Each shaft has a diameter of 20 mm and a shear modulus of G=65 GPa. When a torque of T= 450 N.m is applied to the CD shaft from the D end;a) Calculate the torsion angle on shaft AB. (Write your result in radians.)b) Calculate the total rotation (torsion angle) of the D end of the CD shaft. (Write your result in radians.)
The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
400 lb-in. 1200 lb-in.. Specifications: Shafts AB, BC, CD are solid material. 500 lb-in., B AB=0.6 in. C dsc-0.75 in. dcp = 0.9 in. Determine: a) The shaft section in which the maximum shear stress occurs and the magnitude of the stress. Now consider that the shaft is tubular with a 0.300 inner diameter. Determine: b) The shaft section in which the maximum shear stress occurs and the magnitude of the stress.