Forward converter has the followingsR=15 ohmVS=60VLx=0.5mHLm=7 mHC=100µFF=35kHzN1/N2= 1.5N1/N3=1D=0.4Determinethe output voltageO 12 VO 15 VO 20 V42 V

Answered: Image /qna-images/answer/837e2778-845c-4651-a8f5-1f3c15047b86.jpg

Answered: Forward converter has the followings…

Forward converter has the followings R=15 ohm VS=60V Lx=0.5mH Lm=7 mH C=100µF Determinethe output voltage F=35kHz N1/N2= 1.5 N1/N3=1 D=0.4

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: A Buck converter has the following parameter. Vin =10V, Vout=4V, Pout=10W. Fsw=100kHz. The parasitic…

A: The given information about a Buck converter is shown below. Volts. Volts. W. kHz.

Q: Cyclo Convertors:AC to AC conversion by using Thyristors draw the Circuit diagram and point out the…

A: Cyclo Convertors AC to AC conversion: The circuit diagram is given as:

Q: The input voltage of a Boost converter is 10V, the duty cycle of the boost converter is 0.25. What…

A: Brief description: For the above given question we need to calculate the value of output voltage of…

Q: Calibrated attenuators are used in digital multimeters to the signal level O a. Increase O b.…

Q: II IV

A: The input to amplitude demodulated wave is amplitude modulated wave.

Q: In a DIA converter, LSB represents 0.2 V. The digital input is (0111) will cause an analog output of…

Q: A boost converter with an input voltage of 5 V dc and an output voltage of 8 V dc will have a duty…

A: Given a boost converter with, Input voltage, Vs=5 V Output voltage, Vo=8 V Duty cycle, α=?

Q: For the circuit shown in Figure 5, if R C = 4 KN, RL= 4KN, R in=0.5 KN, IB = 50 µA and IC = 5 mA, а.…

A: Given:RC=4 kΩRL=4 kΩRin=0.5 kΩIB=50 μAIC=5 mAVin=10mV

Q: Plot the graphs of the outputs of the circuits in scale according to the input signal. and provide…

A: a) The diode is biased to the front and thus no signal appears on the output during the positive…

Q: The resolution of an 8 bit A/D converter for a 110V input range is 39.22mV/LSB 10V/LSB 8mV/LSB O…

A: Given that 8 bits n = 8 Full scale value VFS = 10 Resolution = VFS/2^n

Q: Solve the base voltage of a voltage-divider bias circuit with Vcc=9V, R1=560k ohms, R2=560k ohms,…

A: We need to find out base voltage for voltage divider bias bjt circuit , first we will find out…

Q: Q1) For the circuits shown in Figure (1), draw the output signals for the shown input signals. R R…

Q: The half - wave rectifier has a load resistance of 0.5 MQ and the input voltage is 5 sinwt V, load…

A: Given : The given circuit is a half wave rectifier circuit. They have mentioned the input…

Q: (a) An AC triangular waveform with peak values of ±2V is used as an input to a comparator. The…

Q: e pinch-off voltage of an n-channel JFET is about

Q: The input voltage of a Boost converter is 10V, the duty cycle of the boost converter is 0.25. What…

A: Given: Boost converter, Input voltage, Vin=10 V Duty cycle, d=0.25

Q: etermine the output waveform for the circuit of Figure +10 V Vin OV R ww 1.0 ΚΩ Vou

A: Given data, Circuit diagram is given as,

Q: Q/ What is the difference between a voltage divider circuit and a buck converter

Q: nown, Find t age is 1v and

A: The operational amplifier can be used for many applications such as an integrator, a differentiator,…

Q: choose the correct answer 4-If the voltage generator is 5 mV in an emitter follower, the output…

A: Input voltage of emitter follower circuit is given, Vin=5 mV

Q: A step up dc/dc converter has input voltage Vs = 9 V, the average output voltage Va = 15 average…

A: A step up dc-dc converter has, Input voltage (Vs)= 9 volts Output voltage (Vo)= 15 volts Load…

Q: A JFET with IDSS= 7.64 mA and VGSoff=-5V. The drain current when VGS=-3.19 V is

A: We need to find out the current for given voltage

Q: Voe 19V Rc 100 n 15 k IGURE 5-42 32. The base bias circuit in Figure 5-42 is subjected to a…

A: Bias current- Bias current is referring to the prime power that is used to basically turn on a…

Q: What would be the likely output voltage VOUT of the figure below? Show your solution. R 9V Tr1 Dz…

Q: 2. The boost converter has parameter 3. The buck-boost converter has parameters Vs = 12 V, D = 0.6,…

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: Determine the period and frequency of oscillation for an astable multivibrator with component values…

A: The astable multivibrator generate square wave. It doesn't require any external triggering pulse.…

Q: What is the minimum detectable temperature change that the A-to-D converter can resolve

A: The minimum detectable temperature change that the A-to-D converter is given by the expression as…

Q: The output voltage of a quadrupler is 220 V. What is the secondary voltage Vm? 55 V 165 V 110…

A: It is given that: Quadrupler output voltage is, Vo=220 V

Q: How is the phase-controlled thyristor turned on? Select one: O a. A gate current is applied with VAK…

A: The solution is given below

Q: C1 3 Vi Vi 2, 20 V 1.0uF Vo R2 1.2k2 Si LV1 =4 V -20 V

Q: 0:0000 R Clock Q

A: The given circuit is asynchronous counter as clock is only provided to first flip flop. Also every…

Q: Which of the following is not true regarding clamper? O A positive clamper adds a positive DC…

A: Option(A) is true because positive clamper adds positive dc to waveform. Option (B) is not true…

Q: In what region the following circuit will be in? +1.8 V o VD O a. Triode O b. None- off the options…

A: We need to select correct option for given circuit.

Q: onvert the ollowing mnemonic program ladder diagra LD 0.00 AND NOT 0.01 LD 1.00 AND 1.01 20.00 20.01…

A: To convert the given mnemonics program into ladder diagram

Q: Determine the output voltage, Vout when : R1= 10000 R2=12818 Vref=5V

Question

Forward converter has the followings
R=15 ohm
VS=60V
Lx=0.5mH
Lm=7 mH
C=100µF
F=35kHz
N1/N2= 1.5
N1/N3=1
D=0.4
Determinethe output voltage
O 12 V
O 15 V
O 20 V
42 V

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

None
Find the voltage transfer ratio when another voltage divider of the same type is connected to the output resistance of thi voltage divider.
A step-up chopper is fed with 200 V. The conduction time of the thyristor is 200 µs and the required output is 600 V. If the frequency of operation is kept constant and the pulse width is halved, what will be the new output voltage?
eletronic circuit analys design
Calculate the base current IB in uA when VCC=18V, VEE=-14V , RB=9881 ohm, RC=13962ohm, RE=10804ohm and B=108
Voltage multipliers take an ac input voltage, and provide an ac output voltage that is a multiple of the input an ac output twice the input none of these a dc output voltage that is a multiple of the input
Rectification is the process of conversion of Select one: O a. DC to DC O b. DC to AC O C. AC to AC O d. AC to DC
Explain why in a voltage divider, the output voltage decreases for lesser values of load resistance RL while in a voltage follower, the output voltage almost remains constant.
ơ: Determine the circuit type and caleulate the output voltage, draw the output waveform. ISV D,=Ge D,=Ge REIKO R=IKO -5V
If the input voltage in the figure below is increased, the peak negative value of the output voltage will +24 V 10 μF R₂ V ov- A 10 k O A. decrease -24 V B. increase O C. not change IN914 www
Please answer 4 and 2 Thank you
Rebuild the following instructions 1. MOV AX, 0000H 2. MOV AL, FFH 3. NOT BL 4. NEG CX