forces in members in AB, BC, AD, and AE.

Q: zain IQ İlı. Saly ibäi The units of length,mass,time-13 are a- Fundamental units. O b-Derived units.…

A:

Q: Two members are connected by pin at point B and loaded as shown: 114.81 N 721.56 N 215.36 N B 75°…

A:

Q: Determine Iy and ky.

A: Solution: Compute the location of the centroid:   Area mm2 Xi , mm AXi larger Rectangle 1…

Q: What is the strain ratio, R = √( Rmax Rmin)? (see eqn. 12.2, page 307) 4.8 O 1.0 02.0 3.8 3.0

A: The given figure is shown below:

Q: 不 k H, k2 H3 k3 NOTE: ト -ごー*

A:

Q: 1.16. Name the two commonly used systems of measurement. How are they related?

A: Brief concept introduction- Systems of measurement are required to express various physical…

Q: Prove that: Y = (Gs+ eS;' Yw 1+e

A:

Q: bläi 6 The resultant of the following .. forces system is 75 N 90 N 20 50° 50 N W+ 30° 40° 120 N 25…

A: Resultant Force: It is defined as the force which represents the two or more forces acting on the…

Q: 750 lb 3 ft 3 ft 2 ft B 30 Ng (b) Determine the Values of Ax, Ay and Nb Ax is Ib. (nearest whole…

A:

Q: H.W 1-Replace the polar equations with equivalent Cartesian equations. 5]. r = cot 0 csc 0

A:

Q: aw дw aw If w = f(r,s,t), r = x-y, s = y-z, t=z-x then + + ?х ду дz о -2 11 о ( 10 2 ( -1 о

A: Answer: 0

Q: PROBLEM 4. Find the resultant of the forces acting on the frame shown and specify where its line of…

A: Taking equilibrium of forces along horizontal direction, we get…

Q: following differentiable function of x and y:

A:

Q: y 200 mm 300 mm → 125 mm 125 mm 60 mm 150 mm

A:

Q: Draw the shear and moment diagrams of the following beams by semi-graphical method. Write the shear…

A: Given: Required  Shear force and bending moment diagram

Q: y(V) – y = 0 1. y" – 10y' + 29y = 0 2. %3D

A:

Q: Fore O, Rectangle, » Distance of Centroid fom x- axis, i-e, (7) A, = (42) (46 +19+21) = 3612 mm2 X,…

A: To Determine Volume using Pappus-Guldinus Theorem.

Q: Find, nearly, the resultant moment about point A. Show F-375 lb F₂-500 b 8A 61-51- 160 16

A:

Q: 1) Find the coordinates of the centroid, xc and yc. 2) Calculate the second moment of inertia Ix' at…

A: Given data

Q: Problem 10.6 - Locate the centroid of the section and determine the moment of inertia of the beam…

A:

Q: E = 29x 1.' ksi Í 6odiut

A: 1. Determine the fixed end moments FEM for span with udl=wl212FEM for span with point load at centre…

Q: | Question 1) Dimension the cross section of the rectangular cross section cantilever bar given ww…

A: From the given date and diagram it is required to find the beam cross section dimension i.e b &…

Q: Draw the following shape using autocad 21 20 19 18 17 16 15 14 13 12 11 10 9. 8 7 6 3 1 1 2 3 4 5 6…

A: To Draw the given Drawing using CAD software.

Q: 1 Determine dy/dx given y = (2u² – 1)7 if u = x + 2

A: To determine the derivative w.r.t. x.   Given, y=2u2-157, and u=x+12   First we must transform the…

Q: 5-3[(4x-y)+2y]

A: The given expression is,

Q: H, = 19 mm, G, 2.51, Pa 1.73 g/cm d, = 0 division, Gauge factor = 0.01 (mm/division) Dial Gauge Dial…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: The moment diagram by parts are base on the moment diagram of O Fully restrained beam O Cantilever…

A: Moment diagrams by parts is a method to solve the determinate beam and find reactions in beam.

Q: Find the derivation 4. y = x? sin x + 2x cos x – 2sin x

A:

Q: Find the volume of excavation required for the area shown in the figure. Each grid point (20 in…

A: Depth of the cut at every location is given find the average depth of cut…

Q: Which of the following most nearly gives the external degree of indeterminacy? 8 28 24 21

A:

Q: State of S and T during Spanish colonization

A: Brief concept- Spanish colonization- The arrival of Miguel López de Legazpi's expedition from Mexico…

Q: 2=38 N Im man k dane Find

A: Introduction : The given figure shows a box which is being pulled by force of 3.8 m . The…

Q: A column has the cross section shown in Fig. P.14.25 and carries a compressive load P parallel to…

A:

Q: Which among the following determines the direction of closing error? a. Tan δ = ΣD/Σ O_b. c. d. Tan…

A:

Q: 6,2 Show that Modulus of Resilience, UR 2E

A: Modulas of resilience is the amount of strain energy stored per unit volume of a body.

Q: po A - W XX '1

A:

Q: A being Write a mass is located i Determine lifting used of 800kg. in the The Ас and 11) Determine…

A: Mass of the steel beam = 800 kgCG of the steel beam is at the center of the span.It is asked to…

Q: x 60% 120° E 0 F₁ = 300 N FREE 45% 45° F2 = 500 N

A:

Q: 2-17. Resolve F, into components along the u and e axes and determine the magnitudes of these…

A: The free-body diagram of the above figure is shown below,

Q: (8.) Draw the following network: a. G follows F but precede H b. G follows D but precede J c. M…

A: To draw the network

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.