FORCE SYSTEM IV. EQUILIBRIUM OF NON-CONCURRENT Example Problem 2: A 12-ft bar of negligible weight rests in a horizontal position on the smooth planes as shown. Compute the distance x at which the load T=100lb should be placed from point B to keep the bar horizontal. Ans. X=4.82ft P=200lb 3ft 30 T=100lb X 45

FORCE SYSTEM IV. EQUILIBRIUM OF NON-CONCURRENT Example Problem 2: A 12-ft bar of negligible weight rests in a horizontal position on the smooth planes as shown. Compute the distance x at which the load T=100lb should be placed from point B to keep the bar horizontal. Ans. X=4.82ft P=200lb 3ft 30 T=100lb X 45

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectuangular wooden beam ( fb = 7.0 MPa, E = 12.9 GPa) ha s across-sectional area of300 mm by 600 mm. The beam has a simple span of five meters. A vibrating machine weighing800 kg is located at the midspan. The machine is working under a constant force of 500 N andaccidentally stopped after 0.7 sec (rectangular pulse). Determine the following:Stiffness, ? = _____________________Angular natural frequency, ?? = _________________ Displacement at t = 0.7 seconds ?(? = 0.7) = _______________________Displacement at t = 1.5 seconds ?(? = 1.5) = _______________________(???)? = _______________
Using moment area method
One end of a uniform wooden beam of length L and weight W is set on a rough floor. A support wire is attached to the beam at a distance of 4L from the other end. The support wire is run horizontally and attached to a post. In this configuration, the beam makes angle e with respect to the vertical. When a ball of weight W is hung at the end of the beam, the bottom of the beam does not slip. Derive an expression for the magnitude T of the tension in the support wire in terms of relevant system parameters. 4L W L W W tan O2W tan 0 Wetne O2Wctne Ө
Question 2 (PLO2, 30 marks) Figure 2 shows a fixed-end beam with point load, P applied at the distance of a from left support. Assume the flexural rigidity EI of the beam is uniform. P kN Length Student Length (m) а (m) P (kN) Mwanza 5 4 a) By using compatibility of slope, determine the support reactions of the beam. Refer the table provided for the value of length, P and a. (20 marks) b) Sketch the shear force diagram (SFD) and bending moment diagram (BMD). (10 mark)
A B A C D Blocks A, B, and C have weights of 93 N, 25 N, and 15 N, respectively. The coefficient of static friction between A and B is 0.3, between B and C, 0.4, and between block C and the ground, 0.35 Determine the smallest force P that will causes impending motion. Determine the friction force between A and B Determine the friction force between B and C
View Policies Current Attempt in Progress The 86-lb force Pis applied to the 210-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force Fexerted by the horizontal surface on the crate. The friction force is positive if to the right, negative if to the left. Assume 4, = 0.43, Hg = 0.34. P Answer: F = i Ib
show sholution aboid shortcuts
Please answer the engineering problem as soon as possible. Answer letter A only.
Make the solution and answer clean and clear, surely to vote it up nees your help ASAP.
Situation 12: The L-shaped frame is made from two segments, each of length L = 6m and flexural stiffness EI = 80 (10) N/m². (w = 50kN/m) W L 59. Determine the vertical displacement of point B. 0.02 ● 0.21 ● 0.20 0.12 A 60. If the distributed load is 15 kN/m, what will be the vertical displacement of point B. ● 0.05 ● 0.6 ● 0.06 ● 0.5
THE COEFFICIENT OF STATIC FRICTION BETWEEN THE BLOCK AND THE PLANE IS µs = 0.2. DETERMINE THE MAXIMUM VALUE OF WEIGHT W WITHOUT CAUSING THE 50-LB BLOCK TO SLIP. D W 45° Answer:
A uniform concrete slab is supported by the two cables as shown. Compute the vertical displacement of the concrete slab. steel Area=300sq.mm L=5m 1m P=18N 4m W=25N Aluminum Area 500sq.mm L=3m