For what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A be zero? If a couple of that same magnitude M were applied in a counterclockwise direction, what would be the value of Ax? For what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A be zero? If a couple ofthat same magnitude M were applied in a counterclockwise direction, what would be the value of Ax?AAnswers:M = iAx=i4.3Y250 lb4.3BM2.8'63°lb-ftlb2.8'

Answered: Image /qna-images/answer/4a60b75a-31a9-4d9e-9a87-69b584d98e0e.jpg

For what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A be zero? If a couple of that same magnitude M were applied in a counterclockwise direction, what would be the value of Ax? A Answers: M = i Ax= i -4.3' 250 lb L--x -4.3" B M 2.8' 63° lb-ft lb 2.8' C

For what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A be zero? If a couple of that same magnitude M were applied in a counterclockwise direction, what would be the value of Ax? A Answers: M = i Ax= i -4.3' 250 lb L--x -4.3" B M 2.8' 63° lb-ft lb 2.8' C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following beam is supported by roller at A and by hinge at B, calculate the reaction at A. 30kN 10 KN / m 6kN · m A 6 m 10 m- 10 m 6 m Answer: AR
Refer to the figure, what is the horizontal component of the reaction at pin B in kN?
Consider the two-member frame shown in (Figure 1). Neglect the thickness of the members. Assume A, B and C are pins. Suppose that w = 5.5 kN/m. Figure 2 kN/m 6 m 6 m 1 of 1 2.5 m 4 m Determine the x and y components of the reaction at A. Express your answers using three significant figures separated by a comma. ► View Available Hint(s) Az, Ay = Submit IVE ΑΣΦ ↓↑ vec - 6.74,32.67 Part B Previous Answers Request Answer X Incorrect; Try Again Determine the x and y components of the reaction at C. Express your answers using three significant figures separated by a comma. ► View Available Hint(s) IVE ΑΣΦ Screenshot ,Cy= 14.74,34.33 kN vec kN
(3) Use Three Moment Equation Method to compute the support reactions of the beam loaded as shown 600 N R₁ im 3m 800 N/m Ra 1200 Nm am 4 R3
E 600 mm D P 400 mm A C - 600 mm- 600 mm- If the applied force P causes the rigid arm ABC to rotate clockwise about pin A through an angle of 0.02°, determine the normal strain developed in wires BD and CE.
For the frame and loadings shown P=270 KN, and F=540 240 mm 240 mm A В 160 mm F 240 mm D magnitude of horizontal reaction at E magnitude of vertical reaction at A magnitude of vertical reaction at E magnitude of vertical reaction at C magnitude of horizontal reaction at C
Given the figure below determine the reaction at A vertical, determine the reaction at C vertical and horizontal, determine the bar force at AB, determine the bar force at BD.
Determine the magnitudes of the reactions at A and B for the beam loaded as shown. Answers: A = B = i i 19200 lb-ft 4' B lb lb 1320 lb/ft 9'
TA Which is the correct equilibrium equation of the system along the direction? 3 m X B C 2 m 1 m 1 m 2 m 2 m D 2 m y A OΣF-TAB TAC+TAD=0 = OΣF-TAB TAC+TAD=0 OF-TAB TAC+TAD=0 Ο OF-TAB TAC+TAD=0 B
Consider the beam shown in (Figure 1). The support at B can be assumed to be a roller. Suppose that w = 7 k/ft Figure 12 ft 12 ft < 1 of 1 Part A Determine the z and y components of reaction at A. Express your answers using three significant figures separated by a comma. [5] ΑΣΦ [. Az. Ay= Submit ▼ Part B Request Answer B₁ = Determine the y component of reaction at B. Express your answer using three significant figures. ΕΠΙ ΑΣΦ vec Pearson J1 vec 3 → ? ? k Revie
1. A compound shaft consisting of a steel segment and an aluminum segment is acted upon by two torques as shown in Fig. P-316. Determine the maximum permissible value of T subject to the following conditions: Tst < 83 MPa, tal < 55 MPa, and the angle of rotation of the free end is limited to 6°. For steel, G = 83 GPa and for aluminum, G = 28 GPa. Steel 2T Aluminum 50 mm Ø 40 mm Ø 900 mm 600 mm
O 4 Question 7 of 15 ---x, m lb lb ^4) ENG