For the wood beam shown in Figure A, assume L = 1.3 m and P = 11 kN. The beam cross section shown in Figure B has dimensions of b = 44 mm and d = 276 mm. (a) Determine the maximum horizontal shear stress in the beam. (b) If the allowable shear stress for the wood is 800 kPa, what is the minimum width b that is acceptable for this beam? P | 2P B |C D Figure A d b Figure B

For the wood beam shown in Figure A, assume L = 1.3 m and P = 11 kN. The beam cross section shown in Figure B has dimensions of b = 44 mm and d = 276 mm. (a) Determine the maximum horizontal shear stress in the beam. (b) If the allowable shear stress for the wood is 800 kPa, what is the minimum width b that is acceptable for this beam? P | 2P B |C D Figure A d b Figure B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A composite beam is made of two brass [E =101 GPa] plates bonded to an aluminum [E =64 GPa] bar, as shown in Figure below. The beam is subjected to a bending moment of 2030 N-m acting about the z axis. Assume b=53 mm, d1=52 mm, d2 =11 mm, Determine: (a)the maximum bending stresses in the brass plates and the aluminum bar. (b) the stress in the brass at the joints where the two materials are bonded together.
!
Two wood box beams (beams A and B) have the same outside dimensions (200mm x 360mm) and the same thickness (t=20 mm) throughout, as shown in the Figure (3). Both beams are formed by nailing, with each nail having an allowable shear load of (250 N). The beams are designed for a shear force (V = 4.0 kN).(A) What is the maximum longitudinal spacing (SA) for the nails in beam (A)?(B) What is the maximum longitudinal spacing (SB) for the nails in beam (B)?(C) What is the largest shearing stress
The simply supported beam shown in Figure 1 (see next slide) spans a distance of L = 6 m and carries two concentrated loads P, which are applied at a distance of a = 1.5 m from the supports. The beam is fabricated by bolting a steel plate between two wood planks (see Figure 2). The wood planks each have dimensions of b = 30 mm and d = 240 mm. The steel plate has dimensions of t = 9.5 mm and d = 240 mm. The moduli of elasticity of the wood and the steel are 12.5 GPa and 200 GPa, respectively. a) Determine the maximum bending stresses produced in the wood planks and the steel plate if P = 8 kN. b) Assume that the allowable bending stresses of the wood and the steel are 8.25 MPa and 150 MPa, respectively. Determine the largest acceptable magnitude for concentrated loads P. (You may neglect the weight of the beam in your calculations.)
The beam AB, shown in Figure 1a, with length L = 4.5 m is subjected to a uniform distributed load w = 13 kN/m and a concentrated moment M = 18 kN.m applied at point B. The beam has a rectangular cross-section with height h = 183 mm, width b = 98 mm, and constant thickness t = 12.5 mm as shown in Figure 1b. Take E = 200 GPa. 1 Determine the slope at point B 2 Determine the vertical displacement at point B [
50 N/m. 3. For the beam shown below, let wo = 90 N/m and w = Wo W1 | A -2 m 2 m 3 m 3 m -2 m Figure 2 Loaded Cantilever Beam a. Find the reactions at A. b. Find the loading function q(x) using singularity functions. c. Find the shear and moment functions V(x) and M(x). d. Determine and plot the shear diagram for the given loading conditions. e. Determine and plot the moment diagram.
Consider the overhanging beam shown in the figure below. (Figure 1) 125 mm 25mm 5mm 8 kN/m 12 KN 75 mm 75 If d = 420 mm, determine the absolute maximum bending stress in the beam.
Question 6 For the loaded beam shown in Figure Q6 below, consider section M-M and determine the following: 6.1 The maximum shear stress in that section 6.2 The shearing stress at point P 12 mm 25 kN 20 kN P 12 mm 100 mm 0.4m 0.3 m 0.4 m 100 mm
!
= The cantilever beam shown in the figure consists of a rectangular structural steel tube shape [E = 200 GPa; I = 95 × 106 mm*]. For 13 kN, Pc = 59 kN, WAB = 50 kN/m, WBC = 24 kN/m the loading shown, determine the beam deflection at point B. Assume PB L₁ = 2.1 m, and L₂ = 3.4 m. Pc PB WAB WBC B A L₂ L₁ VB = mm C X