For the thrust bearing shown below, normal stress developed due to the loading. Please choose the correct order of average normal stress developed acorss cross section passing B, C and D.

Q: A spherical stainless-steel tank having an inner diameter 'D', is used to store natural gas at a…

A: The given values are- diameter d =620 mm, p= 25MPa , T=1000 MPa , FOS= 3.4 The stress in sphere is…

Q: The beam is subjected to the load at its end. Take P= 3.9 kN and V = 2.3 kN. (Figure 1) Part A…

A: Given data: P =3.9 kN V= 2.3 kN Need to determine the maximum principal stress at point B.

Q: RAH A 60° RAV wwww 500 N E 60° 3m 60⁰ 60⁰ D RBV = 112.89 N RBV = 156.82 N RBV = 206.73 N O RBV =…

A: Given: find the vertical reaction of the roller at B.

Q: UT FOR CONCENTRIC 回SS, Fy (MPa) 0 5-222 222 32 S 寸 246 288 288 244 287 286 19739 241 284 282 322 074…

A:

Q: Determine the forces in members DE, EI, FI, and HI of the arched truss. The forces are positive if…

A: Given diagram:

Q: EXERCISES 4.1 A steel bar of diameter 15 mm is loaded as shown in Fig. 4.28. Calculate the stresses…

A:

Q: A 100 mm long solid cylindrical part shown here has 15 mm diameter. The loads on the part are: 10 kN…

A:

Q: View Policies Current Attempt in Progress Two solid cylindrical rods (1) and (2) are joined together…

A:

Q: A cap plate at the bottom of the brace distributes the load P = 660 kN to four flange plates…

A:

Q: The tank shown in Figure below is fabricated from t = 1/8 in steel plate. The naximum longitudinal…

A:

Q: A cylindrical steel tank is manufactured based on the following data: internal pressure: 36MPa…

A:

Q: If o, = 20 ksi, o, = 10 ksi, and ty = 30 ksi, what is the absolute maximum shear stress for the…

A:

Q: Q2/ Find the diameter of steel rope required to lifting a machine of 3.25 tones weight safely, if…

A:

Q: The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. (Figure 1) Figure…

A: According to the given datad=12 int=0.25 inP=280 psiWe need to findLongitudinal and hoop stress when…

Q: A stress of $=(0,-2,1) MPa acts on a plane whose normal î lies in the same direction as the vector…

A: Given Data: S→ = 0,-2,1 MPa=0i^-2j^+k^N→=(10,3,-8)=10i^+3j^-8k^ Find: Magnitude of shear Stress on…

Q: b) Determine the maximum gas pressure and the dimensions of cross -section of the connecting rod for…

A:

Q: Calculate the Shear Force Value at x=5m from A (in kN to 1 d.p.) 50 kN 50 kN A 2m B 2m C 2m D 2m 50…

A:

Q: Learning Goal: To calculate the shear stress at a point in the web of an l- beam section subjected…

A: To Find : The moment of inertia of the whole cross sectionThe value of QThe shear stress at a point…

Q: B C Problem 1 D B 1.3 What is the value of the shear force at x = 1.5 m? A 6 KN 10 kN 15 kN Don't…

A: Write the given data. P=10 kNL=2.5 mx=1.5 m

Q: Question 15 of 15 Refer to the figure shown a = 11.7 x 10/°C a = 23 x 10/°C -6 %3D E 200 GPa 70 GPa…

A:

Q: For a min. principle stresses of 30MPA when will the rock fail? Draw the two faults on the resulting…

A: Mohr's circle is a two-layered graphical portrayal of the change regulation for the Cauchy stress…

Q: Problem 3: A cylindrical tank with an outer diameter of 1.2 m will be pressurized to 3 MPa internal…

A: To findWhat is the minimum wall thickness of the tank to guarantee a safety factor of 2.5 against…

Q: ads also act on the rod: P = 1700 lb and Q = 1400 lb. Assume a = 15 in. and b = 30 in. Determine the…

A:

Q: Part A |Fucl = 0.97 D HÅ 5m 2 m Determine the magnitude of the projected component of the F= 5 kN…

A: Determine the magnitude of the projected component of the F= 5 kN force acting along the axis BC of…

Q: R₁ $D₁ P = 20 kN = Mv 600 Nm. $D₂ R₂ D3 *** D₁ = 34 mm, D₂ = 40 mm, D3 = 36 mm, R₁ = 5 mm, R₂ = 2…

A: Draw the shear force diagram  P=20 kN, MV=600N.m

Q: SAQ 2 (Stress) The members of the structure in Fig. P-120 weigh 200 lb/ft. Determine the smallest…

A:

Q: If P 4 kN, determine the stress in the inner spring and the displacem of the plate. The inner spring…

A:

Q: Q. After a puncture a driver is attempting to remove a wheel nut by applying a force of P KN to one…

A: Dear Student since you have posted a question with multiple sub-parts, but as per Q& A…

Q: 05) Find the minimum volume of the truss shown with constraints on the depth of the truss (v),…

A:

Q: thickness, t, if t

A: To determine the pressure vessel thickness, tgiven , ultimate strengthyield strength endurance…

Q: Current Att Consider a point in a structural member that is subjected to plane stress. Normal and…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.