For the system shown in Figure, Maximum shear force is : *50KN2kN/mB1m.4m16 kN at point AO 14 kN at point BO 14 KN at point CO 16 kN at point Cun in Figure, Bearing stress at (B) is: *

Answered: Image /qna-images/answer/b8fca8ec-5cbe-4f5c-9ac1-39b73ef35f13.jpg

Answered: For the system shown in Figure, Maximum…

Engineering

Mechanical Engineering

For the system shown in Figure, Maximum shear force is:* 50KN 2kN/m A C 1m 4m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.11P: -11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0...

See similar textbooks

Related questions

Q: the beam shown in Figure (2), determine transverse shear stresses E, F and G on the cross section.…

A: Given P=100kNINA=470016mm4

Q: A beam is loaded and supported as shown, with F1 = 2050 lb, F2 = 2080 lb, M = 6070 ft*lb, and w =…

A: Draw a free-body diagram of the given beam. Apply force equilibrium in a vertical direction.…

Q: Let's consider a fixed supported beam subjected to a triangular distributed load as shown in the…

A: Let us mention reactions developed at fixed end in the figure: We can replace given UDL of w =…

Q: Consider a circular plate, which is clamped/fixed around the edge and subjected to a uniform…

Q: For the simply supported beam with loads as shown below, find out the values of shear force and…

A: For the simply supported beam with loads as shown below,Find out the values of shear force and…

Q: Consider the beam in the figure below. Determine the formulas for the shear force V (x) and bending…

Q: Home Work: 1. Draw shear force and bending moment diagrams for the beam shown in figure. 30kN 2m B…

Q: 50 kN 250 mm 10 500 mm 1450 3 100 kNm 4 8. 7 6 The area of each boom is 150 mm2 and the thickness of…

Question

For the system shown in Figure, Maximum shear force is : *
50KN
2kN/m
B
1m.
4m
16 kN at point A
O 14 kN at point B
O 14 KN at point C
O 16 kN at point C
un in Figure, Bearing stress at (B) is: *

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A solid aluminum bar (G = 27 GPa ) of diameter d = 40 mm is subjected to torques T = 300 N - m acting in the directions shown in the figure, Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
A solid circular bar of steel (G = 78 GPa) transmits a torque T = 360 N - m. The allowable stresses in tension, compression, and shear arc 90 MPa, 70 MPa, and 40 MPa, respectively. Also, the allowable tensile strain is 220 x 10-6, Determine the minimum required diameter d of the bar, If the bar diameter d = 40 mm, what is Tmax?
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A cylindrical pressure vessel having a radius r = 14 in. and wall thickness t = 0,5 in, is subjected to internal pressure p = 375 psi, In addition, a torque T = 90 kip-ft acts at each end of the cylinder (see figure), (a) Determine the maximum tensile stress ctniXand the maximum in-plane shear stress Tmjv in the wall of the cylinder. (b) If the allowable in-plane shear stress is 4.5 ksi, what is the maximum allowable torque T\ (c) If 7 = 150 kip-ft and allowable in-plane shear and allowable normal stresses are 4.5 ksi and 11.5 ksi, respectively, what is the minimum required wall thickness
A prismatic bar is subjected to an axial force that produces a tensile stress ????=65 MPa and a shear stress T??= 23 MPa on a certain inclined plane (see figure). Determine the stresses acting oil all laces of a stress element oriented at ?? = 30°, and show the stresses on a sketch of the element.
An aluminum tube has inside diameter dx= 50 mm, shear modulus of elasticity G = 27 GPa, v = 0.33, and torque T = 4.0 kN · m. The allowable shear stress in the aluminum is 50 MPa, and the allowable normal strain is 900 X 10-6. Determine the required outside diameter d2 Re-compute the required outside diameter d2, if allowable normal stress is 62 MPa and allowable shear strain is 1.7 X 10-3.
An element in pure shear is subjected to stresses ??xy= 3750 psi, as shown in the figure. Using Mohr’s circle, determine the following: (a) The stresses acting on an clement oriented at a slope of 3 on 4 (sec figure). (b) The principal stresses. Show all results on sketches of properly oriented elements.
A vertical pole of solid, circular cross section is twisted by horizontal forces P = 5kN acting at the ends of a rigid horizontal arm AB (see figure part a). The distance from the outside of the pole to the line of action of each force is c = 125 mm (sec figure part b) and the pole height L = 350 mm. (a) If the allowable shear stress in the pole is 30 MPa, what is the minimum required diameter dminof the pole? (b) What is the torsional stiffness of the pole (kN · m/rad)? Assume that G = 28 GPa. (c) If two translation al springs, each with stiffness k =2550 kN/m, are added at 2c/5 from A and B (see figure part c), repeat part (a) to find dmin. Hint: Consider the pole and pair of springs as "springs in parallel."
‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
-18 through 7.3-22 An element in plane stress (see figure) is subjected to stresses o, a., and (a) Determine the principal stresses and show them on a sketch of a properly oriented element. (b) Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element. 7.3-18 a=2I50kPa, ay=375kPa.Txy.=-460kPa
3-17 The stresses at a point along a beam supporting a sign (see figure) are sx= 2250 psi, sy,. = 1175 psi, and txy = -820 psi. (a) Find the principal stresses. Show them on a sketch of a properly oriented clement. (b) Find the maximum shear stresses and associated normal stresses. Show them on a sketch of a properly oriented element.
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.