For the rock element, shown: Calculate the following stresses of interest: a. What is rock's maximum principal stress? b. What is rock's minimum principal stress? c. Normal Stress at Failure Plane A-B d. Shear Stress at Failure Plane A-B

Q: The bar shown in the figure has a square cress section for which the depth and thickness are 40 mm.…

A: we need to find out the average normal stress and average shear stress acting on the material along…

Q: The stresses at a point in a bar are o1 = 29 N/mm2 (tensile) and 02= 14N/mm2 (compressive) as shown…

A:

Q: indicated in the figure. Using the equilibrium equation approach, determine the normal and shear…

A: Given data in question  Stresses Angle To find out  Normal and shear stresses

Q: point, another plane B, inclined at 45°, on the normal aly Mohr's stress circle technique to find…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 75 MPa and 5, =…

A: Given data in question  Stresses Angle To find out Normal and shear stress

Q: 3. Given the following stress functions, = 3x² + 3y² − σ₁ = 3y² o₂ = 3x+y-z+ 6x = -Z Tay=z-6xy-² T₁₂…

A: Given data,

Q: The brass sculpture with a height of 10m experiences shear forces of 30,000N. The area of the face…

A: To find the stress and the strain-

Q: A hydraulic punch press is used to punch a slot in a 0.50-in.-thick plate, as illustrated in Figure.…

A:

Q: Show the type of stress distribution over the radius of the disk 3. How is the correspondence…

A: The area of the middle section of the rod is reduced with respect to both ends which means the disk…

Q: If the principal stresses in a plane stress problem, are 0₁ = 100 MPa, o₂ = 40 MPa, the magnitude of…

A: Given- Principal stresses- σ1=100 MPa,σ2=40 MPa, It is needed to find the magnitude of maximum shear…

Q: Determine the stress components at point A and point B. And show the stress states for these points…

A: Solution; The given cantilever beam is The radius of the beam (r)=6 mm

Q: At a point on the free surface of a stressed body, a normal stress magnitude of Sy = 61 MPa (C) and…

A: step 1-

Q: ) For the given stress condition find: 1. Principal stresses and their orientation. 2. The stresses…

A:

Q: (a) A state of stress at a point is the result of two separate actions that produces the stress…

A: Given data Shear stress (τ) =-15 MPa Axial stress (σy) = -35 MPa θ1= 30°…

Q: The stresses shown act at a point on the free surface of a machine component. Normal and shear…

A: Solution Given Data Sx=12.7 ksiSy= 1.7 ksiSxy=5.8 ksiβ= 34 degrees

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx - 60 MPa and Sy=…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes ares, indicated in the…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 2000 psi, Sy =…

A:

Q: a.) Determine the maximum normal stress developed in the bar when it is subjected to a tension of P…

A:

Q: a. Determine principal stress values b. Calculate the maximum inplane shear stress and average…

A:

Q: For the state of stress given in the illustration below, determine the normal and shear stresses on…

A: Given, Horizontal stress (compressive), σx = 7250 psi  Vertical stress (tensile), σy = -29000 psi…

Q: Q. No .3 On the free surface of an aluminum [E = 10,000 ksi; v = 0.33] component, the strain rosette…

A: εn =1/2(εx + εy) +1/2(εx – εy) cos 2θ +γxySin 2θ/2

Q: Determine the stress components at point H. And show the stress state for this point on a volume…

A: Given Data: Axial Load for Point H is P=3 kN. Shear Load for Point H in Y direction is VY=0.5 kN.…

Q: QUESTION 1 a) A bar 30 mm in diameter and 80 mm in length is subjected to a tensile load 100KN. The…

A:

Q: 2. For the given state of stress shown in figure 2. + 48 MPa Figure 2. a. Construct Mohr's circle…

A: The principal planes are those on which only the normal stresses act with the shear stress zero. The…

Q: 3. A thin hollow sphere of radius 75 mm and thickness 30 mm is subjected to an internal pressure of…

A:

Q: EXAM QUESTION 2 The state of plane stress at a point is represented by the element shown in the…

A:

Q: Find the stresses ox,, Oy,, and Tx,y, on an element oriented at an angle 0 = 30° clockwise from the…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Direct tensile stresses of 120 MN/m and 70 MN/m' act (at a point) in a body on mutually…

A:

Q: 1 MPа 4 MPa 5 MPa state of plane stress

A:

Q: Refer to the figure 1. Which of the following most nearly gives the value of the major principal…

A: Given Normal stresses 200 and 120 kPaShear stress 40 kPaAngle= - 15°To find out Principle stress…

Q: The bar shown in the figure has a square cress section for which the depth and thickness are 40 mm.…

A: Axial force and load on rectangular cross-section = 800 N  Cross-section area = 40mm x 40mm  Average…

Q: At a point in a stressed material, the stress combination acting on a plane is a 90 kPa compressive…

A: (a) The Mohr's circle for the stress combination is shown below. The radius of the circle from the…

Q: 2. Show the type of stress distribution over the radius of the disk

A: From the given figure, it can be seen that the area of the disc is reduced in the given section…

Q: If the principal stresses in a plane stress problem, are 01 = 100 MPa, 02 = 40 MPa, the magnitude of…

A: Given- Principal stresses- σ1=100 MPa,σ2=40 MPa, The magnitude of maximum shear stress=?

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sy = 85 MPa and S, =…

A: Given data in question  Normal stresses Angle To find out  Normal and shear stress

Q: B 35° A 315,2 kPa 131,6 kPa 35° 53.6 kPa 131,6 kPa wwwww 315,2 kPa wwwwww

A: