Direct tensile stresses of 120 MN/m and 70 MN/m' act (at a point) in a body on mutually perpendicular planes. What is the magnitude of shearing stress that can be applied (at that point on those mutually perpendicular planes) so that the major principal stress at the point does not exceed 135 MN/m. Determine the value of the minor principal stress and the maximum shearing stress. Hint: The state of plane stress at a point. Tey

Direct tensile stresses of 120 MN/m and 70 MN/m' act (at a point) in a body on mutually perpendicular planes. What is the magnitude of shearing stress that can be applied (at that point on those mutually perpendicular planes) so that the major principal stress at the point does not exceed 135 MN/m. Determine the value of the minor principal stress and the maximum shearing stress. Hint: The state of plane stress at a point. Tey

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer as soon as possible
The state of stress at a point with ox, oy, and txy as shown. Analyze the state of stress at the point using the Mohr's circle of stress. Determine the following a) Principal stress, b) Maximum in-plane shear stress and c) Normal stress on the plane defined by x' axis where the angle is 25 degrees. Ne To 0. ox x TEV
A state of stress is specified in the figure shown below. Determine the Normal stress σy (mPa) on the Principal Plane if P1 = -5 mPa; P2 = 39 mPa and v = 21 mPa
At a point in a stressed material, the major principal stress is 66 kPa compression and the minor principal stress is 34 kPa tension. (a) Use the Mohr’s circle to determine the shear and normal stress on a plane 45° ccw from the major principal plane. (b) Determine the stress combination acting on the plane 75° ccw from the major principal plane.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If 0 = 68 MPa, determine the principal stresses acting at the point. 114 MPa 66 MPa 157.9 MPa and -155.4 MPa 82.0 MPa and -83.7 MPa O 121.2 MPa and -138.0 MPa O 167.4 MPa and -98.1 MPa O 133.2 MPa and -131.2 MPa
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o = 25 MPa in the direction shown, determine the principal stresses at the point. 28 MPa 16 MPa O 39.2 MPa and -30.2 MPa O 31.6 MPa and -35.8 MPa 54.1 MPa and -41.3 MPa 35.8 MPa and -27.4 MPa O 27.7 MPa and -39.0 MPa Save for Later eTextbook and Media Attempts: 1 of 3 used Submit Answer
Provide correct answer
Q.b.
At a point on the free surface of a stressed body, a normal stress magnitude of Sy = 63 MPa (C) and an unknown positive shear stress exist on a horizontal plane. One principal stress at the point is 9 MPa (C). The absolute maximum shear stress at the point has a magnitude of 81 MPa. Determine the unknown stresses on the horizontal and vertical planes and the unknown principal stress at the point. S, Sxy S Answers: i MPa Txy = i MPа Op2 = i MPa
Please help me with this question.
Topic.p stress problem.
A