For the pipe system shown, find the length of pipe 4 if Q1 = 1m3/s, Q2 = 0.35m3/sand Q7 = 0.27m3/s. Use f = 0.02. *Your answer 1374Pipe #1DiameterLength500 mm100m2400 mm200m3300 mm300m450 mm?400 mm200m450 mm165.85m7500 mm350m8300 mm200mLO

Answered: Image /qna-images/answer/5948e6ac-84ef-445a-b2ce-e8573511a144.jpg

Answered: For the pipe system shown, find the…

Engineering

Civil Engineering

For the pipe system shown, find the length of pipe 4 if Q1 = 1m3/s, Q2 = 0.35m3/s and Q7 = 0.27m3/s. Use f = 0.02. *

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve the following equations 64. y" + 3y - 28y = 10e 4x
Three wires are connected at point D, which is located 18 in. below the T-shaped pipe support ABC. Determine the tension in wire BD when a 257 Ib cylinder is suspended from point Das shown. Round off only on the final answer expressed in 3 decimals and indicate unit. 0024.png ... `24 in. В 16 in. ` 24 in. 22 in. A 18 in. D 180 lb
= For the beam shown, calculate the beam slope at D. Assume that a = 4.4 ft, b = 6.6 ft, c= 8.8 ft, w=1350 lb/ft, P = 3200 lb, and El 537000 kip-in.². A Answer: OD i a W B b P TV rad C D
For questions 1 to 5, consider a bent rod fixed at the wall at A and is acted upon by a 20- N force (parallel to the z-axis) and a 50-N force (parallel to the y-axis) applied at points B and C, respectively. y₁ Z A -4 m- F = (-50j - 20k) N, C = (100i +80j - 200k) N-m F = (-50j) N, C = (100i +80j - 200k) N-m F = (-50j - 20k) N, C = (200i +40j - 100k) N-m F = (-50j - 20k) N, C = (100i + 80j) N-m C -2 m- 50 N 20 N. B 4. Which of the following best valuates the equivalent force-couple set at A of the applied forces 20 N and 50 N? Note: F is the resultant force and C is the resultant couple X he support at A? R are force reactions and M are
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The 13-lb bar AE is suspended by a cable that passes over a 5-in.-radius drum. Vertical motion of end E of the bar is prevented by the two stops shown. The value of μs=0.30 between the cable and the drum. Mo A B C D W 5 in. 5 in. 3 in. E Determine the corresponding force exerted on end E of the bar. The corresponding force exerted on end E of the bar is 314.8 lb
Find the moment (kN-m) at point A if the following data and figure are given: 1 square = 1 sq.meter F1 = 6 kN %3D F2 = 13 kN %3D F3 = 16 kN C1 = 23.kN C2 = 25 kN %3D %3D (Input the value in two (2) decimal places only without the unit) F1 C. 2 F3 C F
Q.5) Three forces are applied to bracket as shown in figure below. Replace the given force system by a resultant force system acting at point O. Then replace the resultant force system by the simplest resultant and locate its line of action as it passes through the y-z plane. 50 mm, 50 mm 100 mm y 100 mm B 75 mm 700 N 30° 45° 1000 N 45° 1200 N 60° E(150 mm, -50 mm, 100 mm)
21 B -32 C D Z2 ▼ Part B As shown, a system of cables supports a bucket. (Figure 2) The dimensions in the figure are as follows: ₁ -5.25 ft, 2 = 1.40 ft. y₁=2.20 ft. 3/2=4.50 ft. 2₁ = 3.25 and 22 = 2.30 ft. If the bucket and its contents have a combined weight of W = 11.5 lb, determine TA. TB. and Tc. the tensions in cable segments DA, DB, and DC, respectively. Express your answers numerically in pounds to three significant figures separated by commas. ▸ View Available Hint(s) TA TB.TC Submit 175) ΑΣΦ | 41 Previous Answers Provide Feedback X Incorrect; Try Again; 4 attempts remaining. Part C Complete previous part(s) vec 6 0 BOA ? lb
PROBLEM 3. (30 PTS.) Use either the Portal Method or the Cantilever Method to approximate all the members' shear, moment and axial forces. Present your answer in the format presented by the SMA (for shear, moment and axial) in the figure below. 0.6P 8 M A P 3 M G D A 5 M 8m A H E B 5 M 8m A 1 F с 4m 4m P= 135kN
100 mm → 20 mm 30 1 140 mm. Xo -20 mm Comment Q1. Determine the moments of inertia of the Z-section about its centroidal x, and yo axes. ,24 mm 1ST O Q2. Determine the location of the centroid x, y and the moments of inertia Ixx and lyy of the shapes shown below. 100 mm -100 mm- Y Le Highlight Draw 20 mm Q ет O L 12 mm TIL ⠀ 100 mm 12 mm FONA Text Fill & Sign More tools 000 000 000 i
A team of house builders went to the Lowe's in Bloomfield, CT and bought bags of Fastset Self Leveling concrete mixes. They built a simple concrete wall for modern looking house, but it is very unstable and temporarily held by two blue cables as shown below. y (a) A В E (b) C X. Da (c) Knowing that the dimensions are (a) 3.5 m, (b) 1.9 m, (c) 1.7 m, (d) 1.4 m, and the tension in cable BD is 600 N. Draw a free-body diagram. Determine the moment about point O of the force exerted by the cable at B.
9.55 A hook is suspended by two steel wires, as shown. The wires are in. in diameter. A load of 1 ton is hung on the hook. Compute the distance that the hook will drop due to the stretch in the wires. //////// 10'-0" (typ.) Nowire. 45° 45° 2000 lb 02.0