For the multi-stage amplifier shown below,given the followingT1: K= 0.12 mA/V², VGS(TH) = 5 V, IDQ = 6.7mA, VGSQ = 12.5 V, RD1 = 4 k, (Assume rd>> Rp)%3DT2: Ipss = 6 mA, Vp = -3 V, IDQ = 2.9 mA,VGSQ = -0.95 V, RD2 = 3.6 kQ. (Assume ra>> Rp)%3DT3: R1 = 48 kN, R2 = 12 kN, Rc =3.6 kQ. ro%3D= 25 kQ, and B = 180Calculate Ayj, Av2, Ay3, and the overallvoltage gain AVT20 VRDI12T322 MBeta10 MAR:18 MO.

T1: K=0.12 mA / V2 VGS(TH)=5 V IDQ=6.7 mA VGSQ=12.5 V RD1=3.2 KΩ(assume rd>>RD) T2:…

For the multi-stage amplifier shown below, given the following T1: K= 0.12 mA/v?, VGS(TH) = 5 V, IoQ = 6.7 mA, VGSQ = 12.5 V, RD1 = 4 k, (Assume ra >> Rp) %3D %3D %3D T2: Ipss = 6 mA, Vp = -3 V, Ipo = 2.9 mA, VGSQ = -0.95 V, RD2 = 3.6 kQ. (Assume rd >> RD) %3D %3D %3D T3: R1 = 48 kQ, R2 = 12 kN, Rc =3.6 kN. ro = 25 kN, and B = 180 %3D Calculate Ay1, Av2, Ay3, and the overall voltage gain AvT 20V Ro T3 22 M Beta 10 MO MO

For the multi-stage amplifier shown below, given the following T1: K= 0.12 mA/v?, VGS(TH) = 5 V, IoQ = 6.7 mA, VGSQ = 12.5 V, RD1 = 4 k, (Assume ra >> Rp) %3D %3D %3D T2: Ipss = 6 mA, Vp = -3 V, Ipo = 2.9 mA, VGSQ = -0.95 V, RD2 = 3.6 kQ. (Assume rd >> RD) %3D %3D %3D T3: R1 = 48 kQ, R2 = 12 kN, Rc =3.6 kN. ro = 25 kN, and B = 180 %3D Calculate Ay1, Av2, Ay3, and the overall voltage gain AvT 20V Ro T3 22 M Beta 10 MO MO

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

How did they get these equations break down simply? Where is ra and rb disappearing to?
Design the fixed bias circuit for the 2N5951 N-channel JFET transistor to achieve an operating point of (Jp=4mA VDS=12 V) if it has a source VDD=24 V, draw the corresponding circuitFrom the datasheet we get VGSOFF=-5V; I_DSS=13 mA
Determine Vx and the mode of operation of the PNP transistor shown in the figure below. Assume Is = °A, B = 50, VA = 00, and Rc = 0.1 KO. 10x10-16 %3D Vcc는 2 V 1.2 V- Rc Select one: a. 0.577 V, Active Mode O b. 0.23 V, Active Mode O c. None of these d. 1.153 V, Active Mode e. 2.306 V, Saturation Mode
The current gain for the transistor in the circuit shown below is B-60, VEn(on) =0.7V and Vic-sat" - 0.2V. For V' = 14.2V when the V, = 3.2V, Rc =8kn and Ic/l =25 find the following: V, Vo Re The value of lc is: O a. 2.188 mA O b. 1.75 mA Oc. 1.4 mA O d. 1.12 mA The value of is Rg: O a. 287.39 kn O b. 229.91 kn O c. 147.14 kn O d. 183.93 kn The value of Vo is: O a. 11.2 V O b.9V O c. 17.5 V O d. 14 V
Basic Electronics
Q1)For the Zener regulator circuit shown in figure ,lf Vi take the following values 10V, 15V, 20V and the circuit has the following properties (VZ=12V,R=1KQ,RL=6KQ and PZmax.=120mW)Find the following Is=IR, .IZ , IL, and VL for each input values R VL PzM
VoD +12 V For the circuit of the adjacent figure a) Given that Ip = 2.83 mA, VGS(om=-7 V and Ipss = 8 mA , find VDs and VGs.. b) If a 50 mV rms input signal is applied to the amplifier, what is the peak-to-peak output voltage? gm = 5000 µS. c) Calculate the output resistance. %3D Ro 10AF 0.1 uF R 10 L. Ra 10 MA 10kn ID= 2.83 mA, Vas (Oef)=-7V. %3D
Given: Vth is 1.2V and k is 0.5 mA/V² Solve for the following with at least 4 significant figures. Current is in mA and Voltages in V. 1. Id, Vgs, Vds. 2. Verify your MOSFET's mode of operation.
Q-2: The Si transistor circuit of the figure shown, find the emitter resistor (RE) that would bias for operating about VcEo = 5V. Let ICEO = 0, B-80, Rg = 220KN, RC = 2KN and Vec = 12V, where Ic # Ig. %3D Vec Re RF Ce RL Rs Vs RE
v*= 5 V 1-) In the figüre for MOSFET circuit; a) R1, R2, RD1, RS1, RS2, VGS1, Vs1, VGS2, VG2 values find it. Rp1 Rị ½(knsw/L) = 0.5mA/V² ½(knzw/L) = 0.2m.A/V² Vri = Vr2 = 1.2V i, = 22 = 0 IpoI = 0.2mA Ino2 = 0.5mA VDsQI = V DsQ2 = 6V R: = 100KQ Rs Cc R. M2 C2 RL = 4 k2 R2 Rs1 Cs Rs2 Rsi = 4KQ V¯=-5 V b) Calculate the voltage gain Ri, Ro and Vo/Vi.
A. Given Vcc= 10V, VEE=-10V, IEE = 1 mA, Rc = 10 kW, VBEon = 0.7V. Determine IC1, VCE1 and VCE2 for the following common mode inputs: 1. Vcm = 0V 2. Vcm = 5V 3. Vcm = -5V B. Analyze what is happening to the VCE for the different common mode voltages. You may relate it to the supplies.
In the circuit given in the figure VT = 25mV, | VBE | = 0.7V, R1 = 515.22Kohm, R2 = 10.89Kohm, R3 = 2.41Kohm, R4 = 1.03Kohm, VCC = 12.00V, VEE = 2.00V, VA = 12.51V, Beta Since = 107.00, Rs = 23.19ohm, Ry = 8.18Kohm, calculate the IC current, Ri, R0 and voltage gain according to the Source (V0 / V1) by making full analysis.