For the MOS transistor in the figure, B=1mA/V² and VTH=1V are given. For the BJT, VBE=0.7V and BF=200 are given. Ica=IDQ =2mA. Find the ac gain (vo/vi) of the circuit. VDD 9V RC R1 10k CB. R2 10k M1 R3 10k

Q: What is mean by equipment grounding and system grounding?

A: As per bartleby guideline for more than one question asked only first three are to be answered…

Q: The BEST choice electronic device to turn a device at a particular voltage is a/an _____. A. PUT B.…

A: the correct option would be SCS. Particular voltage can be obtained by adjusting firing angle of scs…

Q: Q1-A LED had been connected to the output 12, write the codes of programing arduino UNO that the led…

A: There are two functions is used to turn ON/Off the LED. void setup(); This is used for the setup of…

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: Sketch the figure and explain in detail about the HVDC circuit breakers

A: Given: The objective is to give an explanation about the HVDC circuit breaker with the figure

Q: Solve the circuit shown when V₁ = 10V, V₂ = 5V, R = 1990 when the diodes have linear models with Vj…

A: In this questionWe need to determine the current in the resistance R as shown the circuit. Given…

Q: Discuss whether NEC provides the maximum requirements or minimum requirements.

A: NEC is the acronym of National Electrical Code.

Q: Identify the type of signal as shown on the following figures. Also, indicate the equation defining…

A:

Q: What is OSHA mission?

A: -OSHA stands for Occupational Safety and Health Administration . It is for the U.S Department of…

Q: Discuss any two types of signalling mode with a neat diagram.

A: two types of signaling mode with a neat diagram

Q: 11- The area of the surface defined by r= 5, 0 < 03,0 <p < is.. 12- The volume defined by 2< p< 5…

A: We will use general formula of area and volume in spherical,  cylindrical coordinates to find the…

Q: The channel _______when Id=Idss. a. does not exist b. is closed c. is narrowest d. is widest

A:

Q: Discuss any two types of grounding methods.

A: Two types of grounding methods: Solid grounding Resistance grounding

Q: I am handling a junction boxes where we are having pre-charge circuit, why is it being used here?

A: A pre-charge circuit is commonly used in electrical systems, especially those involving high-power…

Q: Explain the Different types of testing Methodologies used in CB??

A: To check the rated characteristics and the capabilities of a circuit breaker, different types of…

Q: The nominal output voltage of a certain regulator is 8 V. The output changes 214 mV when the input…

A: Given The nominal output voltage of a certain regulator is 8 V. The output changes 214 mV=0.214Vwhen…

Q: What type of circuit does PLL look like over its lock range?

A: PHASE-LOCKED LOOP (PLL): 1. In the frequency demodulation technique, frequency synthesisers, and…

Q: For the circuit shown in the figure below, com

A:

Q: Several components on a computer's motherboard are connected through parallel electrical conducting…

A: We need to explain components on a computer's motherboard are connected through parallel electrical…

Q: Explain the different type of routin test In CB ??

A: There are different kinds of routine tests done for the Circuit Breaker.   Power frequency…

Q: How about the Norton Resistance (RN) of the circuit?

A:

Q: Q.26 Why is shielded wire used for signal runs? Select one: A. TO PREVENT VOLTAGE SPIKES B. TO…

A: From this question we need to know why we use shielded wire for signal runs :

Q: Short circuit test measure half load copper loss. True or False

A: The explanation is as follows.

Q: List two important uses Loop (PLL) in of phase locked analog Communication System.

A: PLL can be used as AM detector for demodulating amplitude modulated signals. Main goal of a PLL is…

Q: Demostrate obtaining 8 to 1 using 2 to 1 multiplexer using the IC 74157 IC. How the connection will…

A: Demostrate obtaining 8 to 1 using 2 to 1 multiplexer using the IC 74157 IC. How the connection will…

Q: In solar module, minimum value of shunt resistance could be 300 Ohm. Select one: True False

A: In solar module, minimum value of shunt resistance could be 300 Ohm.  Select one: True False

Q: How many conductors are required to address eight devices? Do those devices need to connect with the…

A: Three conductors are required to adress 8 devices because by using three bits we can form 8…

Q: There are a number of importance of measurement and instrumentation system. Identify and explain 5…

A: importance of measurement and instrumentation system: Product development: Measurement and…

Q: What is the minimum distance between conduits in a junction box straight through pull? A. 6 times…

A: The correct option from the given options will be option D) 12 times. For junction box calculations,…

Q: How does the BMS system in EVs work?

A: The BMS system in an Electric Vehicle (EV) is a critical component that manages the performance and…

Q: 2. Explain over modulation.

A:

Q: Due to the effect of the resistance of the cable connected to RTD, two-wire cables up to ……. meters…

A: c) 50-195

Q: A compound generator is to Supply aLoodof 250lamps; -each radedtoow, 250v.CTnear mature, series dind…

A:

Q: What are common methods for assessing the reliability of electronic components in a system, and how…

A: Assessing the reliability of electronic components in a system is crucial to ensure the proper…

Q: 5. (a) What is the full form of the word "LASER"? Explain how stimulated emission amplifies light in…

A: (a) LASER: The full form of LASER is "light amplification by stimulated emission of radiation". A…

Q: Define Digital

A: In the context of electrical engineering, Digital is a type of signal which is active at only…

Q: 4. The band gap is the energy difference between the valance band and the conduction band. In any…

A: The bandgap is the difference between the valence band and the conduction band. The conduction band…

Q: Give a brief description for under/over voltage time relay.

A:

Q: Programming the device involves the blowing of internal fuses to achieve a desired_________________…

A: PLD is an IC that contains enormous no of entryways, flip-flops, and so forth that can be arranged…

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.