Answered: For the lightweight truss which is…

For the lightweight truss which is loaded as shown 10 kN 5 kN -6 m 6 m A B 4 m D -6 m 3 m 3 m By using the Vector Approach and the Method of Pins, determine

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.125P: The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A...

See similar textbooks

Related questions

Q: The assembly shown is supported by pin supports at A and B, and consists of four members connected…

Q: A 50 lb force is applied to the wrench. Solve for the pin reaction at B as well as the gripping…

Q: The beam consists of two bars connected by a pin at B. Neglecting the weight of the beam, compute…

A: This beam can be divided in two parts about the hinge point B. And, the right part is where, RB and…

Q: is formed in a quar- C6-67 The lever shown in Fig. ter circular arc of radius 20 in. Plot A and B,…

A: Where, FB = force acting at joint B. RX = horizontal reaction at A RY = vertical reaction at A

Q: 6b. Find out all possible FBD/FBDs to solve for all the components of the support forces exerted by…

Q: Find the reaction at A due to the uniform loading and the applied couple. The force reaction is…

Q: The beam with riveted bracket is subjected to the couple and a force as shown in figure, and their…

A: The reactions at point A can be determined as,

Q: 2 kips B 2 kips E -4 panels at 10 ft = 40 ft span 2 kips G 8 kips H 10 ft

Q: Ap 60° B 4 m- - 4 m- E 4 m 60° P

Q: 1. A 120-kg block is supported by a rope which is wrapped 1 times around a horizontal rod. Knowing…

Q: 4- In order to raise the flagpole OC, a light frame OAB is attached to the pole and a tension of 780…

Q: Assuming clockwise moments as positive, compute the moments of the two forces about points A, B and…

A: Given data: side=1 m Need to determine the moment about the points A, B and C.

Q: 1. Draw free-body diagrams (FBDs) for the specified rigid bodies. Then, write the coordinates of…

A: A bent pipe structure is givenTo find:(a) Draw free body diagram.(b) Write the coordinates of each…

Q: 4/106 In the special position shown for the log hoist booms AF and EG are at right angles to one an…

A: Let us consider the link EFG tanθ=18θ=tan-118=7.125°

Q: For the loaded structure shown, beam AB and strut BC are made from a GI rectangular tube with width,…

Q: Solve the support forces Ay and By of the truss below, as well as the rod forces acting on rods O3,…

A: The reaction supports are calculated as : ΣFy=0Ay+By-1-2-3=0Ay+By=6…

Q: Answer the following question: 4. Find the forces at points A and B of the landing gear shown.

Q: In the special position shown for the log hoist, booms AF and EG are at right angles to one another…

A: Given Data: Weight of the Log W = 4380 lb Find: Compute the magnitudes of the forces supported by…

Q: Ok A 30k 20 k 20 k 20 k 30k 30 ft- 30 ft 30 ft- 30 ft

Q: Solve for the reactions where the beam is fixed to the wall at A.

A: According to the given data A free-body diagram is shown below We need to find Reactions at Point…

Q: 9m 12 kN/m | с 15 kN/m 10 m D B + -5 m E 6 m

Q: The 480-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the…

Q: 30 kg 30 3/14: To facilitate shifting the position of a lifting hook when it is not under load, the…

Q: Pin A, which connects the 200-kg steel beam with the center of gravity at G to the vertical column,…

Q: 2. The coefficient of static friction µ, is the same between block B and the horizontal surface and…

A: GivenWA=WBcoefficient of friction =μs

Q: The 470-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the…

Q: Homework: Determine the horizontal and vertical components of the pin reaction at B on CE of Figure…

A: moment at pt A, ByX3+50X3X3/2+1/2X200-500X3X3/2+1000X11-1000X2=0 By=3187.5N VERTICAL COMPONENT OF…

Q: The beam consists of two bars connected by a pin at B. Neglecting the weight of the beam, compute…

A: The free body diagram of beam BC is shown below:

Q: Determine the magnitude of the resultant force and its inclination with the horizontal and where it…

Concept explainers

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.

Question

For the lightweight truss which is loaded as shown
10 kN
5 kN
-6 m -
6 m
VA
C
4 m
D
-6 m
3 m
3 m
By using the Vector Approach and the Method of Pins, determine the force in member AB (kN), by analysing joint A.
Answer:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Show the complete solution: The frame shown in Figure is supported by a hinge at E and a roller at D. Compute the horizontal and vertical components of the hinge force at C as it acts upon BD.
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 20i - 14j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN. Quiz 2. 9, 2 m 17 4 m Finish Time lI 6 m 曲

ab 32 4 in 8 in 44R The assembly shown has the dinensions given above. When a force of F 220 ib is applied, find the tension in the rope, and the force that body CDEG exerts on body ABC at point C. Note: The distance AG is delberately not provided Forces: T 541.6717557b Fe 118 6095643/b(Denote a nghtward force with a positive value, a leftward force with a negative vale
DUE NOW. Please answer it correctly. Thanks!
Use the method of Sections To Compute The Internal Axial Forces In Members CD, CE, And EF.
Each member of the truss is a uniform 16-ft bar weighing 540 lb. Calculate the average axial force in each member due to the weights of the members. The axial forces are positive if in tension, negative if in compression. 60° 60° 60° 60° A 16' B 16' Answers; AB = i Ib AE = i Ib BC = i Ib BD = i Ib BE = i Ib CD = i Ib DE = i Ib
A pulley of 1ft-radius, supporting a load of 500 lb, is mounted at B on a horizontal beam as shown. If the beam weighs 200 lb and the pulley weighs 50 lb, find the hinge force at C.
The rigid frame loaded as shown has pins at support A and D. The connections at B and C are rigid. The frame is loaded with a uniform load (3k/ft) acting on member BC, it has a triangular load (6k/ft) acting on member CD, it has an applied couple of 30 ft-K at point B and a concentrated load of 12K at point C. Determine the reactions and draw the moment diagram. Use Ax as the redundant force reaction. EI is constant.
Calculate the force in member GH of the truss and indicate whether it is in tension or compression, using either method of joints or method of sections. Required: Draw the FBD(s) as needed for analysis-all equilibrium equations must correspond to a FBD that you have drawn. Make sure to clearly indicate which FBD your equation(s) correspond to. K J H 4 ft C - 3 ft 3 ft -- 3 ft- 3 ft-3 ft 1500 lb 1500 lb 1500 lb 1500 lb 1500 lb
The T-bar AEBF is connected to rod CD, with the joint at F being equivalent to a slider bearing. The supports at A and C are slider bearings, and thrust bearings are found at B and D. The two applied forces, which act at the midpoint of the arm EF, are parallel to the y- and z-axes, respectively. Neglecting the weights of the members, draw the FBDs for the entire structure, the T-bar, and rod CD. Determine the total number of unknowns.
4.6.6. For the structure loaded as shown, find the horizontal and vertical components of the pin force at B as they act upon member CD. (use method of members)
2. Using method of members, find the horizontal and vertical components of the pin force at B as they act upon member CD in the structure shown below. 60 lb 240 lb B 20' 10 10' 10'