For the hydraulic system shown, Qi is considered as the system input and Q3asthe system output. Determine the system state equation.A2

Answered: Image /qna-images/answer/01f4a856-122d-4882-a078-ed54a581a141.jpg

Answered: For the hydraulic system shown, Qi IS…

For the hydraulic system shown, Qi IS considered as the system input and Qzas the system output. Determine the system state equation.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem #3 - Modeling, Mixing Problem Two tanks are connected by pipes in parallel as shown in Figure 2. Tank 1 starts with 160 lb of salt dissolved in 200 gal of water. Tank 2 starts with 100 gal of pure water. Using the diagram below, solve for the particular solutions of salt concentration in each tank as a function of time. Plot the solutions in Excel on the same plot. Note: some flow rates have been intentionally left out of the diagram below; use the conservation of mass to determine those. As a thought experiment, consider what negative eigenvalues imply. What would it mean if the eigenvalues were positive instead (what would the math say)? i.) ii.) iii.) iv.) v.) vi.) vii.) Use a conservation equation to develop your differential equation model (you should end up with two ODEs to describe the change in salt in both tanks). Write your system of ODEs in matrix form. Set up the eigenvalue problem and then determine the eigenvalues. Use the eigenvalues to determine the…
5.46 Two streams discharge into a pipe as shown. The flows are in- compressible. The volume flow rate of stream A into the pipe is given by Q = 0.02r m³/s and that of stream B by g = 0.008/² m³/s, wherer is in seconds. The exit area of the pipe is 0.01 m². Find the velocity and acceleration of the flow at the exit at = 1 s. 28. ei P PROBLEM 5.46 Answer: V2.8 m/s A=0.01m² a = 3.6 m/s²
1. A weight of 8 lbf is attached to the end of a vertical spring which stretches 4 inches before reaching equilibrium. If the weight is pulled down 6 inches below equilibrium point and given an initial upward velocity of 8 ft/sec, find the equation of motion. Note: In solving for the spring constant k, make sure it ends up as a positive number.
Scenario Mechatronics is an integrated and interdisciplinary approach to engineering design. A leading supplier and systems integrator of highly dynamic, automated logistics solutions for warehousing, production, picking and distribution operations is looking for a resident engineer to provide electrical, mechanical and software solutions. As the first stage in the interview process, you need to show your understanding of electrical mechanical models and components. Derive an equation relating the input force F, with the output, displacement x for the mechanical system shown * Sketch the response that you would expect for this system and state what happens as c is altered. What type of system response is this V F(t) Derive the relationship between output, the p.d. across the capacitor, and the input v R с Sketch the response that you would expect for this system and explain the importance of the time constant to this response? What type of system response is this?
Find the equations of motion of the system using the law of conservation of energy.
Expanded.3 deals with the conservation of momentum principle. Using the conservation of momentum principle to solve this problem is mandatory. Solution using other approaches will be automatically considered false. For the problem related to Expanded.3, sketches of the system showing: • the respective initial and final velocity and position coordinates and the frame of reference considered • the forces acting on the system of considered, in other words, a free body diagram (FBD) are mandatory. Their absences will automatically make the problem false. The automobile has a weight 3,158-lb and travels forward at 8ft/s when it crashes into the wall and stops. The impact occurs in 0.04 s. If the coefficient of kinetic friction between the wheels and the pavement is 0.42, and the brakes are applied, what is then the average impulsive force?
The equation of motion for the system shown in figure is m Fecosot
Problem 3. The dynamics for a cruise control system are given as Mÿ(t) + bý(t) = u(t) where u(t) is the input force, y(t) is the displacement of the car and b is the viscous friction coefficient. Find GZAS (z) for the system.
Q4 Find the transfer function for a single translational mass system with spring and damper
Q2: You ride your bike along a straight line from your house to a store (1000 m) away. On your way back, you stop at a friend's house which is halfway between your house and the store. Find: a. What is your displacement? b. What is the distance you have traveled?
Fluid: Consider the following two tank system, where an input flow enters the first tank with flowrate Qri and travels through a pipe of fluid resistance Rf to fill up the second tank. The fluid then flows out of the second tank through an orifice governed by the square-root orifice equation for pressure drop, Qf,0 = k(Pza). Find the linearized system equations written in terms of pressure. Note that P1 and P2 are pressures relative to atmospheric pressure (not absolute pressures) Qti Pa = constant C1, P, R, C+2, P2 k Q1
Draw proper FBDS and derive the differential equations of motion for the system below. Write just the state equations in vector matrix form. mi ft) V Yy, Kz Mz VYz