1. The deformation of the fluid will continue as long as theis applied.2. When designing gates, vessels, dams or other bodies that are submerged in a liquid, it is important notonly to estimate thebut also to specify its location on the body.3. The surface tension is the tensile force perin any direction along the surface the surface tension.4. The value of ---------- s pecifies whether the fluid can be assumed compressible or incompressible.5. Archimedes' principle indicates6. A truck is filled with gasoline. If the container (tank) on the truck undergoes athen the liquidsurface will begin to rotate clockwise about the center of the container and will eventually maintain afixed tilted position.

1. The deformation of the fluid will continue as long as the is applied. 2. When designing gates, vessels, dams or other bodies that are submerged in a liquid, it is important not only to estimate the 3. The surface tension is the tensile force per but also to specify its location on the body. in any direction along the surface the surface tension.

1. The deformation of the fluid will continue as long as the is applied. 2. When designing gates, vessels, dams or other bodies that are submerged in a liquid, it is important not only to estimate the 3. The surface tension is the tensile force per but also to specify its location on the body. in any direction along the surface the surface tension.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids—castor oil (0.96) and water. Considering a unit-width of the gate, apply the PRESSURE PRISM CONCEPT (Illustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z = 7m. FIND: A. The hydrostatic force due to linseed oil F1. B. The hydrostatic force due to castor oil F2. C. The hydrostatic force due to water. D. The net hydrostatic force acting on the gate Fnet
What would be the rotation rate (in rad/sec) if during rotation the water in the right leg (with a diameter of d) decreases a distance h1=0.03 m? A U-tube, Elevation = 20 cm d - 20 сm 2d → Elevation = 0 -20 cm- B 20 cr A
Problem 2 The apparatus sketched in the figure below serves as a viscometer i.e. it can be used to measure the viscosity of a liquid. In the drawing, D is a large reservoir containing a viscous liquid A and E is a cylindrical tube of radius R, open at both ends, surrounding and coaxial with B, which is a cylindrical "bob" of radius êR that is dragged up through the fluid by a frictionless pulley system (C) utilizing a weight W. Determine a design equation that relates the viscosity of the liquid to the geometry of the system and the weight W. Hint: you can assume that the length of the cylindrical tube is sufficiently long for the flow to reach steady state. W E D B
Q1:-The gate AB as shown in fig.1 has long 1 m and wide 0.9 m.Find the force F on The gate AB and also find the centre of pressure X 8 m 3 m 1 m Oil A 1 m S=0.81 7 m B 50 Fig.1
Global warming will produce rising sea levels partly due to melting ice caps and partly due to the expansion of water as average ocean temperatures rise. To get some idea of the size of this effect, calculate the change in length, Ah (in mm), of a column of water 1.5 km high for a temperature increase of 1.2 °C.Assume the column is not free to expand sideways. As a model of the ocean, that is a reasonable approximation, as only parts of the ocean very close to the surface can expand sideways onto land, and only to a limited degree. As another approximation, neglect the fact that ocean warming is not uniform with depth. Properties of water: 3 = 210 x 10 /C. c= 4186 J/kg - °C, L; = 334 kJ/kg, Le = 2256 kJ/kg Enter you answer below (to the nearest mm): Ah (in mm) = Type your answer.
Ql:-The gate AB as shown in fig.1 has long 1 m and wide 0.9 m .Find the force Fon The gate AB and also find the centre of pressure X 8 m 3 m 1 m Oil A 1 m S=0.81 7 m 50 Fig.1
4.Surface tension of water in contact with air at 23°C is given as 0.0717 N/m. Pressure inside a droplet of water is to be 0.0149 N/cm2 greater than the outside pressure, calculate diameter of droplet of water.
State Pascal’s principle and give one application of the principle. An object is dropped into a beaker of water. Two forces are operating on the object viz. the weight of object and the buoyant force FB due to the fluid. Explain, in terms of the forces when the object. a.) Sinks to the bottom of the beaker b.)Floats in the water A hydraulic press for compacting powdered samples has a large cylinder with a diameter of 10.0 cm and a small cylinder of diameter 2.0 cm. If a force of 350 N is applied to the small cylinder, what will be the force exerted by the fluid on the large cylinder? Be consistent with your units.
1.32 A 1.5 in diameter shaft rotates in a sleeve bearing which is 2.5 in long. The radial clearance between (he shaft and the slecve is 0.0015 in, and this is filled with oil having , = 1.$3 x 10-2 lb/ft•s Assuming rotational speed of 62 rpm and a lincar velocity gradient in the lubricating oil, determine the resistive torque due to viscous shear at the shaft-lubricant interface. Ans. 0.0079 ft-lb
The surface tesnion of waterr in contact with air at 20deg C is given at 0.0716 N/m. The pressure inside a droplet of water is to be 0.0147 N/cm^2 greater than the outside pressure, calculate the diameter in mm of the droplet of water. a.2.43 b.4.62 c.3.60 d.1.94
P1.5 An artificial solar pond is a body of water with a density gradient created by adding salt to the water. Obtain an expression for the variation of pressure P with depth - assuming the density distribution to have the linear form, p(=) = p, + az, where Po is the density at the surface and a is a constant. The ambient pressure is Po. [Answer: P(z) = P, + gz(p. + az /2)]
For a liquid with the contact angle of 53.6 degrees and surface tension of 0.075 N/m, capillary rise is 2.50 m. What is the expected capillary rise in meters if the liquid is replaced with another with a contact angle of 12.7 degrees and a similar surface tension? (answer should be accurate to 2 decimal places) Answer: