For the gravity concrete dam shown in the figure, the following data are available:- The factor of safety against sliding (F.S sliding) =1.23Unit weight of concrete (Yconc) = 24 KN/m- Neglect( Wave pressure, silt pressure, ice force and earth quake force)μ = 0.65, (Ywater) = 9.81 KN/m³Find factor of safety against overturning (F.S overturning)6m180m10m5m+

Answered: Image /qna-images/answer/df2837b5-0e43-4bac-94dc-cfef7a6d3c61.jpg

For the gravity concrete dam shown in the figure, the following data are available: The factor of safety against sliding (F.S sliding) =1.2 - Unit weight of concrete (Yconc) = 24 KN/m³ - Neglect( Wave pressure, silt pressure, ice force and earth quake force) μ = 0.65, (Ywater) = 9.81 KN/m³ Find factor of safety against overturning (F.S overturning) 10m 6m1 5m Th 80m k X

For the gravity concrete dam shown in the figure, the following data are available: The factor of safety against sliding (F.S sliding) =1.2 - Unit weight of concrete (Yconc) = 24 KN/m³ - Neglect( Wave pressure, silt pressure, ice force and earth quake force) μ = 0.65, (Ywater) = 9.81 KN/m³ Find factor of safety against overturning (F.S overturning) 10m 6m1 5m Th 80m k X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An embankment load on a silty clay soil layer as shown below. Determine the stress increase under the embankment at points A and B that are loaded at a depth of 6 m below the ground surface. 5 m 1H:2V 1H:2V 1H:1V 8 m 13 y=18 kN/m Y=18 kN/m³ 6 m : B : A CS Scanned with CamScanner
You have been assigned to check the stability of a pond constructed in stiff saturated clay underlain by a layer of sand. The necessary information are given in the following figure. (i) Find effective stress at and determine the stability of cut under given condition. (ii) What should be water level into the pond to ensure factor of safety = 1. (Given that yw = 9.81 kN/m³) H = 5 m 7m KE T 3 m 2 m ↓ Saturated clay Sand Ysat 18 kN/m³ 6.5 m Ysat = 15 kN/m³
A building is founded on a rectangular mat of dimensions 20 m x 10 m as shown in the plan view in figure below. A surcharge of 300 kPa is applied within the area ABCD whereas a surcharge of 100 kPa is applied within the area CDEF. Calculate the increase in vertical total stress in kPa at the depth of 5 m below Point F
The plan of a flexiblerectangular loaded area is shown with a uniformly distributed load q =100 KN/m2. Determine the increasein the vertical stress (A6z) at Z= 2.0 meters bel ow (a) Point A = (b) Point B= (c) Point C= 4 m 1.6 m- 2 m 0.8 m q = 100 kN/m? C 1.2 m-
Regarding geotextiles used in separation, what is the required burst pressure of a geotextile supporting 75-mm maximum-size stone and heavy trucks with a tire inflation pressure of 1000-kPa? Use (where p’ = the pressure at the geotextile interface and p = the inflation pressure); a cumulative reduction factor = 2.0; and a factor of safety = 2.0.
Figure Q1(c) shows the soil profile with groundwater table is 6 m from thesurface impermeable layer. Calculate the total stress, pore water pressureand effectives tress at points D.
17. A cast-iron pipe of 750 mm diameter is used to carry water under a head of 60 m. What is the approximate thickness of the pipe if permissible stress is to be 20 MPa? (Take specific weight of water as 9.81 kN/m³) (a) 22 mm (c) 11 mm (b) 14 mm (d) 7 mm
Styles Editin A production casing was planned to run in the production hole of a well with casing shoe at 15,000 ft. When casing was run empty to the mid depth, collapse safety factor was calculated to be 1.9. When the casing was at the bottom and full of a certain mud, safety factor of the collapse was calculated to be 2.75. If the mud weight of the fluid in the annulus was 14.0 ppg, determine the casing collapse rating and mud weight of the fluid inside the casing.
A building is founded on a rectangular mat of dimensions 20 m x 10 m as shown in the plan view in figure below. A surcharge of 300 kPa is applied within the area ABCD whereas a surcharge of 100 kPa is applied within the area CDEF. Calculate the increase in vertical total stress in kPa at the depth of 5 m below Point F (acceptable tolerance = 10%).
There is a flood that takes place above the ground surface up to 1.3 m in height. Assume the unit weight of water is 10 kPa. Calculate the effective stress at the top of ground surface. 13 kPa -10 kPa O O kPa -13kPa
k Il.pdf iL| C/Users/YONAST%20TSIGHE/Downloads/BYG504%20G%20Geoteknikk%201l.pdf 2. A.) Plot the distribution of total stress, effective stress and porewater pressure along depth of soil as shown in Figure 1 (water table 4.5 meter from its surface). Plot effective stress paths for the lower layer of soil at rest by assuming the soil has an internal friction o'= 30°. B.) As consolidation test on a sample taken at bottom showed: 2-0.3, K = 0.05 and v' = 0.3, calculate the sample's effective elastic bulk moduli E' and shear modulus G; Find the changes of such parameters when the water table rises to its surface. 4-0.7, sE035 4.5m. Figure 1. Layers of soil site