4 m 1.6 m- 2 m 0.8 m 100 N2

Q: Given: A0A1=10.250m B1B2=0.735m Determine the distance A1B2 in m

A: Here Reduction to MSL concept is using As height is increasing then readings is also increase to…

Q: PLEASE DO THIS TYPEWRITTEN ONLY FOR UPVOTES. DO THIS ASAP

A: Given data in question Loads Span member length  Dimensions  To find out  REaction at joint A

Q: 10 kip 2 kips/ft 10 ft 15 ft

A:

Q: i. | 20KN 10KN/n 3M 3M 3M 3M

A:

Q: Find degree of static indeterminacy

A: Given data : The number of member in truss structure m=21 The number of Joint in truss structure…

Q: 20 k G 15 ft 10k E F 10 k 10 ft C. 20 k 20 k 25 ft 15 10 25 25 10 15 ft ft ft ft ft ft

A:

Q: Five forces are acting on the cantilever beam AB. Find the resultant or a couple acting on the…

A:

Q: solve for the total head loss given that the pressure drop between the junction=250kPa. (f=0.02)…

A: To determine the total head loss.   Given, Length of pipe (1), L1 = 875 m Length of pipe (2), L2 =…

Q: A C-channel has a dimensions of as shown, in mm, with a thickness of 75 mm. Determine the moment of…

A:

Q: Column2 700mm 1 3m Beam2 4 3. 700mm+ Column1- 3 3 1 +350+ . 4 350 15. 2 2 2 Beam3 5m Beam1 1 11 4m…

A: Volume of BEAM 1= (4-0.35/2-1.050/2)*0.35*0.45= 3.3*0.35*0.45= 0.51975= 0.52 m3 Volume of BEAM 2=…

Q: Question Bank - Friction Two concrete blocks weighing 1800N each form part of the retaining wall of…

A:

Q: 1.) Determine the resultant of the forces acting on the body. 450KN 600KN 2 1 4 200kN 15 12 2 250kN…

A:

Q: 8KN 2KN A Z 3M am 3m

A:

Q: 75 N/m 800 N - m B 8 m-

A:

Q: 10 N 0.6 m 0.4 m 10N Which of the systems is/are equivalent to the couple to the figure at the top…

A:

Q: Problem 3 Five forces are acting on the cantilever beam AB. Find the resultant or a couple acting on…

A:

Q: Determine the moment of inertia of the shaded area with respect to y-axis Where: b1=10mm; b2=42mm;…

A: solution here there are four cross section Two webs of 10 x 140 mm2center flange 84 x 50 mm2lower…

Q: A- Determine the moment of inertia about the x axis. B-Determine the moment of inertia about the y…

A:

Q: A 8 k 6k 9 ft 4 ft- 4 ft- 4 ft B 2 k/ft

A: See image below to see the explanation how to get the reactions.

Q: For each shaded area, determine the following: The moment of inertia about the x-axis The moment of…

A:

Q: Determine support reaction

A: Apply equilibrium condition : ∑FX=0∑FY=0∑M=0Sign convention :Clockwise moment is taken as positive…

Q: + kNm hinge 2 EN/m 24 N 5 m

A: Calculate support reaction Hinge at c  Determinate beam

Q: 3: Determine the magnitude of the Maximum shear force in the beam Vmax = 7.5 kNO Vmax = 50 kNO Vmax…

A:

Q: Q.5: Locate the maximum Moment at a distance X from the support A Maximum moment at X= 2.0 m O…

A: Given data  UDL Span length  Overhanging beam

Q: H 4 kN I 60° D E F G A C B mim 2 m 2 m

A: Explanation of above answers are :

Q: 20kN/m 20kN/m 1m 2m 1m 1m 5m

A:

Q: ?----=In fig. D1= 50 mm, DO=25 mm, p1-p2= 20000 pa., CO=0.7 ,Q P₂ 0 0.0025 m3/s O

A: Given, D1 = 50 mm  Do = 25 mm  ∆P = 20000 Pa  Co= 0.70

Q: 5 cm 12 cm 12 cm N1-2 0 = 30° N1-10 5 cm 15 cm

A: The problem involves determining the forces and moments acting on a mechanical system to ensure it…

Q: 400 N 2m 2m 2 m 45 P 2m

A: Note: As nothing is mentioned in this question so we are assuming that we have to calculate support…

Q: 200 Tco 300 150

A:

Q: Which of the following equations is CORRECT? All symbols carry their usual means. v² 30(=+G) a) SSD…

A: Stopping sight distance (SSD) is the distance required for a driver to bring their vehicle to a stop…

Q: Calculate the moment of inertia about the y axis using integration y (cm) -1- x (cm) -1-

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: Determine the force of all members using METHOD OF JOINT. Answer in 3 decimal places only. TRUSS…

A: Objective: To determine the force of all members of the given truss using the method of joints.…

Q: RAy= kN 3) 4m t 3m t2un t

A:

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.