For the given power system, Generators: Transformers: a) Compute the table below: Base Power Base Voltage Base Impedance Base Current ZGI ZTI 300 MVA, 20 kV, X"=20% 300 MVA, 220/20 kV, X=10% Z Transmission Lines T₁ Zone 1 (G₁) 20 kV 200 KV 1750 c) Draw the reactance diagram of the system. 175 200 KV WT₂ b) Determine the per unit value of each quantity with respect to the system base. VG2 VGI Zone 2 (Transmission Lines) 200 KV 1750 ZG₂ ZT2 300 MVA Zone 3 (G₂) VG3 ZG3 ZT3 Zone 4 (G3)

For the given power system, Generators: Transformers: a) Compute the table below: Base Power Base Voltage Base Impedance Base Current ZGI ZTI 300 MVA, 20 kV, X"=20% 300 MVA, 220/20 kV, X=10% Z Transmission Lines T₁ Zone 1 (G₁) 20 kV 200 KV 1750 c) Draw the reactance diagram of the system. 175 200 KV WT₂ b) Determine the per unit value of each quantity with respect to the system base. VG2 VGI Zone 2 (Transmission Lines) 200 KV 1750 ZG₂ ZT2 300 MVA Zone 3 (G₂) VG3 ZG3 ZT3 Zone 4 (G3)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Vbase_zonel Sbase_zonel . * For the power system shown in Figure Q1b, calculate the per unit impedances of all components with given zone 1 voltage base 22kV and power base 100 MVA (for the system). = 22 kV = 100 MVA Generator: . YG₁ Zone 1 100 MVA 22 kV (0.1+ j0.5) pu 1 . E 1 T₁ YY Transformer 1: 100 MVA 25/130 kV (0.1+j0.5) pu Zone 2 L = (10+j100) S2 Figure Q1b. T₂ Zone 3 YA Transformer 2: 50 MVA 110/33 kV (0.1+j0.5) pu M₂Y Load (motor): ● 50 MVA . 33 kV (1+j0.5) pu
The subject EE463 Power Systems analysis Please show all steps , and in clear writing it is better in hand written form.
Solve it fast plz
Here X =165 plzzz solve urgent with detail...
A load of 1600 kW at 0-8 p.f. is shared by two 1000 kVA transformers having equal turn ratios and connected in parallel on their primary and secondary side. The full load resistance drop is 1% and reactive drop is 6% in one of the transformers, the corresponding values in the other transformer being 1.5% and 5%. Calculate the power and power factor at which each transformer is operating.
Q)The question is that how kW is converted to kVA in complex form and how kV square is 2.4 for T1,T2,T3 can you plz explain it by seeing the solution
Please help
For a 50 kVa distribution transformer, which on its high voltage side is 2400 V and on the short-circuit low voltage secondary has a voltage of 240 V with a frequency of 60 Hz, it has a leakage impedance of 0.72+j0.92 Ω on the high voltage side and 0.0070+j0.0090 Ω on the high voltage side low tension. The short-circuit test presented values of 48 V, 20.8 A and 617 W for high voltage. The impedance responsible for the excitation current is 6.32+j43.7 Ω referring to the low voltage side. One open circuit test, with the low voltage side energized, presented the values of 240 V, 5.14 A and 186W. According to the information presented, determine: a. Draw the equivalent circuit on the high voltage side and present the impedance values in the circuit. b.Draw the equivalent circuit on the low voltage side and present the impedance values in the circuit. c. For the high voltage value, calculate the value of the current flowing in the magnetizing impedance. d.Determine the yield for an…
6. A generating station has the following daily load cycle : 10–12 Time (hours) 0–6 6–10 12–16 16–20 20–24 Load (MW) 20 25 30 25 35 20 Draw the load curve and find (i) maximum demand, (ii) units generated per day, (i) average load, (tv) load factor, II
Power engineering book Mehta
There single-phase transformers are 3 transformers (Each of them is to be connected Delta-Delta) is rated at 50kVA, 2200/400 V , Zeq = 1.4 + j1.8 ohms (Ref. the high-voltage side of the transformer). The high voltage side of the transformer receives 2200 V by the transmission line (impedance of transmission line is 0.15+j0.80 ohms). The Low voltage side of the transformer disburses load by the transmission line (impedance of transmission line is 0.001+j0.003 ohms). Determine Load Voltage when the transformer works at rated by PF=0.85 lagging
7- d. e. f.