For the given beam below, the 8 KN load is changed to 87 KN and the 4 KN load is also changed to 35 KN. Use E=200GPa and I=30x105 mm². Using Double Integration Method, with point A taken as origin, Calculate the deflection at point D, yp in millimeters. Express your answer in 2 decimal places. Include (-) sign if the calculated deflection is negative. 8 kN -3m 1 D 3m = B. + 1 -3 m 4 kN C

For the given beam below, the 8 KN load is changed to 87 KN and the 4 KN load is also changed to 35 KN. Use E=200GPa and I=30x105 mm². Using Double Integration Method, with point A taken as origin, Calculate the deflection at point D, yp in millimeters. Express your answer in 2 decimal places. Include (-) sign if the calculated deflection is negative. 8 kN -3m 1 D 3m = B. + 1 -3 m 4 kN C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please assist using macaulay's method
Two hard rubber blocks [G = 320 kPa] are used in an anti-vibration mount to support a small machine as shown. Determine the downward deflection that will occur for an applied load of P = 930 N. Assume a = 26 mm, b = 46 mm, and c = 80 mm.
Take ur time but please solve this Thank u
Determine the maximum deflection for the beam shown by: Double integration method the final answers should be range to 143 to 146 mm
. Consider a beam with length L which is embedded at its left end and free at its right end, with w(x)=wo exp(-2x/L). Find the deflection of the beam, y(x), and plot yEI/woL vs. x/L.
For the beam loaded as shown in the figure below, determine the following unknown using any geometric method. Consider 250 mm x 400 mm (b x h) section and E = 120 GPa. a. Deflection at C in mm. Enter absolute value only. Use a = 3.2 m, b = 23.5 kN/m, and c = 26.7 kN c kN b kN/m B "a" m
From the beam shown below, determine the maximum deflection and maximum slope of the beam. Find also the deflection and slope 3m to the right of point A. Use Double Integration Method.
Determine the deflection at points B and C of the beam shown. Values for the moment of inertia of each segment are indicated in the figure. Take E = 200 GPa.
1. A beam is loaded as show in the figure. Using Virtual Work Method determine the following: a. Deflection at C b. Slope at E Assume El is constant 12 KN 12 KN B Im-Im 2m- 10 kN D 2m 10 kN E
For the beam shown, calculate the beam slope at A. Assume that a = 77 in., b = 264 in., c = 87 in., w = 0.37 kips/in., P = 6 kips, and EI = 1336000 kip-in.2.Answer:θA = Type your answer here rad
Determine the ff. unknowns on the beam shown using CONJUGATE BEAM METHOD. Consider 250 mm x 250 mm section and E= 200 Gpa. Computer for: a.) Deflection at point B in mm b.) Maximum deflection on the beam in mm Dont forget that the given values are: a= 6.5 m b= 38 kN-m c= 15 kN Provide complete solution. PLS ANSWER ASAP. I'LL RATE, THANKS
Give me right solution with clear calculations. Use moment area method