For the given 7-m simply supported nonrectangular SRB (f'c = 27.6 MPa & fy = 275 MPa which carries an ultimate dead load of 15 kN/m, determine the ff: 1. Equivalent compressive force 2. Steel Ratio 3. Design moment strength 4. Allowable service concentrated live load placed at 2-m from left support.

For the given 7-m simply supported nonrectangular SRB (f'c = 27.6 MPa & fy = 275 MPa which carries an ultimate dead load of 15 kN/m, determine the ff: 1. Equivalent compressive force 2. Steel Ratio 3. Design moment strength 4. Allowable service concentrated live load placed at 2-m from left support.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

From the given figure below, determine the minimum height of the beam if the flexural stress is not to exceed 50kPa. Assume width of beam is 200mm (JN 10 N/m 0- T 3M RA=42N 42N B IM TEMA 12N 75NM 81NM, Im RD=3N EL -3N 0° 78 Nm 3NM V-DIAG M-DIAG
PLEASE SHOW YOUR COMPLETE SOLUTION.
PROBLEM 2: The steel beam loaded below has the built-up cross section as shown. Determine the maximum permissible value of the load w so as not to exceed allowable bending stresses of 110 MPa. -125 mm- w (including beam weight) 20 mm 20 mm 100 mm .-- NA A B - 2 m - 6 m 20 mm FINAL ANSWER: Max. allowable w kN/m
in 21- ő A steel beam is reinforced by three steel rods. The modulous of elasticity for concrete is 20Gpa and for steel is 200Gpa. Maximum allowable stress for concrete is 9.45Mpa and for steel is 140Mpa. Calculate the largest allowable positive WBT bending moment in the beam. иа mo maod motinu od o boblow need sved Ha bus 400mm aidT (alonnerlo ert to rigiow stongi)/4000E of Trup 200-0 signs or botuesom sWnworla es berloss M bris V zsra erli owob stiW maod sdi to mergeib insm brol bus borlism tuo sallimill nollor 10 nige over on The modulus of elasticity for concrete is 20Gpa and for the steel is 200 Gpa. Allowable stress for concrete is 9Mpa and for steel is 140Mpa. Calculate the maxium allowable bending momemt that can be applied per metal rod of the concrete slab. 150mm 200mm D=16mm 140 mm -22mm Diameter TOPABA t 50mm T 140 mm 140 mm 140 mm
2. The column shown in the figure is reinforced with 6 - 25mm diam steel with fy: = 415Mpa and f'c = 27Mpa a. Determine the nominal load pn when e = 200mm b. Determine the nominal load when e = 350mm C. 250 mm 65 mm 400mm 65 mm e CD Pn
1. A steel column 10 m long is fabricated from a cover plate and C section arranged as shown. Determine the safe compressive load. Fy = 248 MPa, E= 200 GPa. Use AISC/NSCP Specs. 450 mm -cover plate 'I 12 mm y2 IP d2 10 m C 310 x 37 A = 4720 mm? d = 305 mm bf = 77 mm tf = 12.7 mm tw = 9.8 mm C 310 X 37 a) Both ends of column are fixed b) Both ends of column are hinged c) One end fixed, the other end hinged Use design values of k. tw d=305- Ix = 59.9x10° mm ly = 1.85x10° mm x = 17.1 mm x=17.1
Please use the NSCP 2015. Thank you.
2) will upvote anyone who will answer
ASAP NEED RIGHT COMPLETE SOLUTION !!! Determine the design compressive strength (kN)
Please refer to Double RC beam and we based on NSCP 2015 (current reference in the design of RC struct) Thank you.. Need this rush atleast 45 mins thank you so much hope you help me.
A simply supported pre-tensioned T-beam, as shown in Figure (2) has: f'ci 25MPa; f'-40 MPa; span length is 12m; Total Aps-800mm² for tendons; initially stress in the tendons is 1000 MPa. Consider 20% the total losses of pre stressed force then determine the allowable service live load can be carrying. 150mm 600mm T 500mm T Aps-800 mm² 50mm 150mm Typical Cross section Figure (2)
Grath fas A cantlever AB o erath lm carries a from klev. uniformly distributed load, wNm fe fired end A to the free end B. Te the cantilever Consista a horizontal thicknees lomm and with 120mm as shown in fhe below, plars plate4 figure calculate the total permiseiblé diafribte load,wif the meximum bending Stress is not exceeding 10OMH/mt. Ignore the grore te weight a the tlefe Im 120mm