For the following questions, select the best possible answer from the give list 1. True or False: The output current of an OP AMP is zero. True OR False 2. When using superposition to solve circuit problems, the independent current sources are replaced by a and the independent voltage sources are replaced by open, short, voltage source in series with a resistor, OR current source parallel to a resistor a [Select] [Select] 3. True or False: Norton's equivalent circuit and Thevenin equivalent circuit are source transformations of each other True OR False 4. When transforming a voltage source into a current source, we can ignore any resistance that is in [Select] parallel OR series

Q: Black to 0.3 0.291 0.00882 3 -2.999 0.036 0.089 0.4 0.364 0.411 Anode -5.999 0.5 0.6 0.7 12 -11.998…

A: Multimeter- It is an electronic device which is used to measure different parameter like voltage,…

Q: (a) Describe the main sources of power loss in a digital integrated circuit. (b) Calculate the…

A: Since, we answer only upto 3parts.So the solution of first three parts are as follows : The major…

Q: Each subsatnce absorbs or emit unoque  level & quantities of energy/  e.m.r..   True  False

A: GIVEN: a statement  FIND: TRUE OR FALSE

Q: What is the required resolution of an instrument if the product characteristic specification is 10.0…

A: The number of bits or portions that the output or displayed reading from a sensor or measuring…

Q: How many valence electrons does a donor atom have? Please choose one: a. 3 b. 4 c. one D. 5

A: Donor atoms are belongs to group V in periodic table.

Q: Convert 24.788832 to six significant figures

A:

Q: 17. Which of the following statements is correct? The resistance of most of the material is…

A: we need to tell which option is correct.

Q: 1. How iron loss in transfomer is minimized 2. On Cwhaf bushing size and comstouction is depending…

A:

Q: Answer the following questions. 1. What is ceramics? 2. Give some examples of Ceramics products. 3.…

A:

Q: a) Explain FOUR (4) measurement standards available.

A:

Q: The maximum number of electrons in each shell of an atom is O a. 2 O b. 8 O c. 2n? where n is the…

A: Electrons are very important as they constitute the flow of currents.

Q: Describe the difference between donor and acceptor impurities.

A: For the given question we have to write the differences between donor and acceptor impurities

Q: Find the value of (1ti).

A: The complex number Can be solved easily.

Q: in el Eocs) / Ei (s)

A: The solution can be achieved as follows.

Q: What is the required resolution of an instrument if the product characteristic specification is 10.0…

A: Resolution is the smallest change that the instrument can measure.  It is the least count…

Q: A transistor is used as a switch and the waveforms are shown below. The parameters are given as…

A: Given  Transistor as switch and waveforms as shown  Vcc=200 vVCE(sat)=1 vICS=100 AICEO=1 mArise time…

Q: Explain the elements of measurement system in detail

A: Measurement system : measurement system is combination of various component which measures the…

Q: S We measured the current that appeared on the plotted screen as shown in the figure by means of…

A: The most popular form is the D'Arsonval galvanometer, which uses a light coil of wire strung from a…

Q: A resistor was measured 13 times at the same time conditions with the following results (in ohms):…

A: Measured resistance values is given by: R1= 100 ohm R2= 996 ohm  R3 = 990 ohm  R4 = 995 ohm  R5 =…

Q: Define the following terms (i) Linearity (ii) Fidelity

A: Linearity is closely related with proportionality. Linearity is represented as a  straight line in…

Q: 4. For 3 hours of pure music, determine the amount of storage needed to record based on 2 channels.…

A: For a pure music, given that: Time taken to play (t) = 3 hours = 3×60×60= 10800 seconds; Number of…

Q: Power across R1 Watts Power across RB = Watts Power across Diode Watts

A: In this question we need to find a power across R1 , RB & diode

Q: A Give the value of each digit in the following decimal numbers: fal 263 tb) 5436 (e) 234543

A:

Q: 10 16 BCD Gray 3-code 10110111 FD 1011001 91 111001

A: Value of binary to decimal is given by:-  Num1 = 27×1+26×0+27×1+25×1+24×1+23×0+22×1+22×1+20×1…

Q: The width of the semiconductor is depends on the amount of impurities added to it. Select one: True…

A: Semiconductor is a matter which have the conductivity between the conductor and insulator. By adding…

Q: A synchronous generator has a constant mechanical input power of Po. In the fault followed by the…

A: Given  A1=1.6 A2=0.4

Q: Germanium Silicon Vo v2 V1 RL 1k 15 mi

A: The given circuit is,

Q: Unit 4: Table 1: Filter information A filter is required to attenuate all signal frequencies above…

A:

Q: 1.53. (a) What is 8(2t)? (b) What is 8[2n]?

A:

Q: What does gv(E) represent? Select one: O a. The number of electrons in the conduction band between…

A: In this question,  We need to choose the correct options What is gv(E) represention?

Q: A resistor was measured 13 times at the same time conditions with the following results (in ohms):…

A: Given: The measured values of a resistance 13 times are,…

Q: What is the Q, FF steady state answer ? Cik Cik Cik

A: The truth table of D flipflop is (for positive edge of clk) Clk D Q Q¯ Comment ↑ 0 0 1 Q output…

Q: None

A: Step 1:Given, mass of unknown solute (w2) = 0.5000 gFormula weight of unknown solute (M2) = 255.0…

Q: nple is Tu e value of the resistivity?

A:

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.