For the following problems: Show all calculations 1. Find the maximum bending stress, fb, in the beam and cross-section shown 12 6kff 61-41 6 I W14 x 90

Q: steel beam of I cross-section is simply supported on a span of 4m. Find the safe uniformly…

A: The given figure is shown below:

Q: Q.No.3: Determine the ACI design moment capacity =60000 psi. Also draw the strain diagram? 4 #9 bars…

A:

Q: The maximum shear stress (kPa) is most nearly 100 kPa 50 kPa -50kPa 50 kPa 75 56 O 66 O

A: Given data : Normal stress in X direction (σX)=-50 KPaNormal stress in Y direction (σY)=-100…

Q: In the steel structure shown (see Figure Q1), a 6-mm-diameter pin is used at B and C and

A: According to given data

Q: < 250 mm A D P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars…

A: E=2G(1+μ)μ=E2G-1 GIVEN E=205GPa G=82GPa NOW USING ABOVE FORMULA μ=2052x82-1 μ=.25

Q: A PROB. 1.8-12 a 2P B (a) D XII Gusset plate Rivet (b) Section

A:

Q: A W18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 29 kips,…

A: Answer  We know that maximum bending stress occur in a beam at extreme fibres and it can be…

Q: 35kN Uniform Load W kN/m Span L L/3 Use the diagram above and the W and L values assigned to you to:…

A: As per guidelines , we will solve only first 3 subparts for this question as it contains more than 3…

Q: simply supported beam 4 m long is carrying a variable load of w = 0 KN/m at the left support and w =…

A:

Q: The maximum shear stress (kPa) is most nearly 100 kPa 50 kPa -50kPa 50 kPa 75 O 56 O 66 O

A:

Q: 6. Given Data and figure shown; Diameter of each rivet = % inch Max. allowable shear stress of rivet…

A:

Q: (d) Radius of Mohr's circle (e) maximum value of the principal stress omax at the junction of the…

A: Question is based on the simply supported beam subjected to concentrated load at center. Properties…

Q: A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers.  The…

A: Bending Moment : Bending moment is a reaction caused on an element or component due to applied…

Q: Problem 2: A bar is made from bonded pieces of steel (E = 29x10 psi) and brass (E = 15x10 psi).…

A: Given : Es = 29 X 106 psi Eb = 15 X 106 Determine the max. stress in the steel and brass when a…

Q: The steel beam has the cross section shown. The beam length is L = 30 ft, and the cross-sectional…

A:

Q: the

A: A device for measuring corneal thickness that is installed on a slit-lamp is known as pachometer. It…

Q: Find the Zero- Force Members at the shape: D. L M 10n 10 t 10 A 10 A 10A 10t 10A 6 kips kups 6 kips…

A:

Q: Q4 - For the given beam and cross section, at point B on section A-A (mid-span), determine the…

A:

Q: The dimensions of a rectangular beam are limited to b = 300 mm and effective depth, d = 700 mm.…

A:

Q: Figure P-130 shows a roof truss and the detail of the riveted connection at joint B. Using allowable…

A:

Q: For the truss and loading shown, determine the magnitude of the normal stress(in psi) in member CE,…

A:

Q: FOR THE LAP JOINT SHOWN, DETERMINE THE MAXIMUM SAFE LOAD 'P' WHICH MAY BE APPLIED IF THE SHEARING…

A:

Q: 30KN A 60kN B 60KN C H 12.0 m 60kN DE G 30kN M tot 3.0 m

A: Method of section:- This method can be used to calculate the specific force in member of a truss.…

Q: What is the Maximum Shear Stress, t, on the centric axially loaded member shown? The cross-sectional…

A: Given data : Axial load (P)=40 kipsCross sectional area (A)=2 in2

Q: 06. The lap joint is connected by three 20-mm diameter rivets. Assuming that the axial load P = 50…

A:

Q: Cross Section k2,5m 6 m- | A75m 1ス5m Determine the Bending Stress at Sectlon D-D

A: Given data in question  Simply supported beam  Dimensions  Cross section Laoding To find out…

Q: 1. Draw the axial force diagram of the rod. The diameter d=10mm, F=5kN. E=210GPa. Determine the…

A:

Q: Problemt The detail of a truss at the support is glued as shown. Given: shearing stress = 800 kN/m?…

A:

Q: The beam shown in Fig. 3 carries a concentrated load of W and a total U.D.L load of 8 Determine the…

A: Safe working load is the older term of working load limit and also It is the breaking load of a…

Q: or the beam with the cross-section shown and loads as follows: w = 2 kN/m, M = 4 kN-m and P kN, =…

A: Given data:

Q: The beam shown below has a cross section of channel shape with width b3200 mm and height h=80 mm,…

A:

Q: With

A:

Q: For the beam below find the normal stress at sections in point (B) and (C) 75 kN 35 kN 45 kN 85kN…

A: T oFind :-  normal stress at B and C in sections of the beam

Q: 1500 lb 4500 b A 2.5 m. E NA- ID 1- 96 in. 8 ia

A:

Q: A short prismatic member is subjected to load P- 100 kips at comer shown by Red Dot as shown in…

A: Given: Load, P= 100 kips A1=3×12=36''y1=122=6''A2=3×12=36''y2=122=6''A3=9×3=27''y3=32=1.5''

Q: 1. The cross-sectional area of each member of the truss is 1200 mm?. Calculate the stresses in…

A:

Q: Consider the truss structure and the loading given below. a) Compute the average axial stress on…

A: Take equillibrium at point B to find force

Q: 00144 0.01am 0.09m 0.0144m 0.09m For the beams shown below: 1- Draw shear force and bending moment…

A: Note:-As per the guidelines we are only supposed to answer first question. With three sub parts.…

Q: Problem 4 The joint is fastened together using two bolts. Determine the required diameter of the…

A: