For the following bandpass filter with component values below the circuit; Choose the correct equation for the transferfunctionV.(s)L = 10 mH, R = 102, C = 100 nFSelect one:O a.O b.C.d.H(jw) =H(jw) =H(jw) =SLH(jw) =1/sCHEjw108w² + jw10³ + 108w10³w² + w10³ + 108jw10³-w² + jw10³ + 108-w² + 108RV,(s)

Answered: Image /qna-images/answer/6dcce284-8414-43f3-a95a-cdb7e2223d5f.jpg

Answered: For the following bandpass filter with…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. Find the transfer function H(w) = Vo(w)/V₁ (w) for the circuit shown a. Plot Amplitude and phase spectrum using MATLAB. b. Hat type of the filter (LPF, HPF, BPF, or BSF). Solution: Vin C₁ 36 1 μF R₂ ww 1 KS2 R₁ 1kQ2 + C₂ HH 0.2 μF OUT
Electrical Engineering will upvote . Need matlab knowledge these are the parts that need to be answered. ons: Calculate the cutoff points. Show a screenshot of your circuit. Are the calculated cutoffs being reflected on the theoretical Bode Plot? Include a screenshot of your codes and the theoretical Bode Plot with both cutoff points labelled. How well did the filter perform when processing the 10HZ and 15OHZ combined signal? Include a screenshot of the Scope. The transfer function for the band pass filter is given to you (equation 9). How was this derived? Show the steps starting from how you use the circuit to get the equations representing the circuit to how you solve the equations to get the final version. Given is that it is an RC Bandpass circuit with r1=10kohm, r2= 100kohm ,c1=1uf ,c2=0.001uf. the RC bandpass circuit proceeses 10hz and 150 hz combination. equation 9 needed for part 4 mentioned above is wC1 R Vw? (RCi+R1C2+R2C2)²+(1–w?C,C2R, R2)2 %3D
Magnitude (dB) Phase (deg) 0 -5 -10 -15 -20 -25 -30 -35 -40 -15 -30 -45 -60 -75 -90 10 Bode Diagram Frequency (Hz) Assume an RC circuit filter has the bode plot shown above. 10* In units of dB, what is the magnitude of the transfer function at f = 900 Hz, |H(f = 900 Hz)|dB? |H(f = 900 Hz)|dB [dB] : _~15 rad B) In units of what is the approximate cut-off frequency, we, for the RC circuit? Do not leave sec' your answer in terms of . rad. We []:
a) Compute the transfer function T(w), the absolute value, and phase at resonant frequency. b) What kind of filter is this? Please answer in typing format please ASAP
For the low-pass active filter shown below, the transfer function is expressed as: V. Zc V: ZR + Zc where: 106 Zc ja rad w = angular frequency in ZR = 2000 ZR V. Vị - Zc Vo can be written as: Vi 4-A) Show that the Vo 500 Vị 500 + jw Vo What should be the value of w so that the magnitude of Vi is ? 4-B) 4-C) With w = 1250 rad/s, and V; = 9ej1.8 – j10 volts, evaluate the magnitude and phase of V. Vo (Hint: evaluate 2 in polar form, and Vị in polar form, then V, = 2x V; ) Vị 4-D) When 4 modules of this filter are cascaded, the total transfer function will be (2) . Use de Moivre's Theorem to find the expression of the total transfer function in polar form. Then, find determine the value of w so that the magnitude of the total transfer function is ? V10
compute the IC SATURATION CURRENT IF BCE IS EQUAL TO 0.4V
For a Low pass filter with a series resistor R = 2 kohms and inductor L = 10 mH with a load resistor RL = 1 kohms, find the: a. transfer function [H(s)] without the load RL b. transfer function [H(s)] with the load RL c. what is the cutoff frequency without the load RL d. what is the cutoff frequency wit the load RL
Find the transfer functions for the circuit and find the cutoff frequencies. calculate. upper cutoff frequency=fcl=? lower cutoff frequency=fch=? Cec=? Notch frequency=fn=?
ANSWERED PLS ALL FOR LIKE
Quèstion 1 For the following RC circuit, R-100 ohm, C- 1pF 1. Derive the transfer function on your test paper. What is the transfer function? 2. If input is 20cos(200t-40) + 10cos(500ot+30), what is the output? 3. What is fu? Sketch the approximate straight line Bode magnitude and phase plot of the circuit on your test paper.
Number 2
The magnitude and phase diagrams are provided for a passive filter. Input signal vin(t)=15 cos(20000t+100°) V is applied. What is the output voltage in V when t-1ms ? Series RLC H(s) -20 -30 -40 700 10 10 180 150 ... ... ... ... 100 ... 50 10 10 Frequency (rad'sec) Phase (deg) Mag (dB)

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS