For the figure shown below. Determine the force exerted on the bar ABC by the cylinder with a mass of 97 kg in the direction towards point B? 20 45° D 2m Im 1m

Q: The shaft shown in the figure left has the diameters 304 Stainless steel - 2014-T6 Aluminum and…

A:

Q: A set of sprockets is constructed, as shown in Figure 1, so that the second and third rotate on a…

A: Solution: Given Data: r1=1 cmr2=4 cmrc=1 cmr3=3 cmN1=y rpmN2=u rpmN3=x rpm   To Find: (a) N1N2(b)…

Q: If R is the rotation matrix, then RRT is a

A: The inverse of a rotation matrix is its transpose, which is also a rotation matrix: The product of…

Q: A 2.00-mol sample of a diatomic ideal gas expands slowly and adiabatically from a pressure of 5.02…

A:

Q: hi, where did u get this R value from. these are the values i have

A: There are two forms of Ideal gas equation which are given below: 1. PV=nRuT 2. PV=mRT Where, P =…

Q: 4. A pair of gears with a reduction ratio of 2.32 operating on 83mm cen- tres is required. The…

A: (h) To find : The output speed. Given : The reduction ratio is : ζ=2.32. The module is : m=2 mm.…

Q: How would you solve this manually without an equation solver

A:

Q: Q (2) Mohammed and Ali drive from Baqubah to Hillah with total displacement of 135.7 km (32.1° north…

A: Given- D1=135.7kmat32.1∘north of eastD2=51.9kmat25.9∘south of easttime t=1.5+1=2.5 hoursTo Find-…

Q: Write force F2 in vector form

A:

Q: 4-15. In a RL circuit, the voltage across the Cinductor V, leads the voltage across the to resistor…

A: In a RL circuit, the voltage across the inductor V_L leads the voltage across the resistor by 90…

Q: A cylindrical steel pressure vessel 400 mm in diameter with a subjected to an internal pressure of…

A: Givendia=400mmthickness t=20mmInternal pressure P=4.5MN/m2

Q: Solve for the general solution and type of auxiliary equation of +y = 0 dx c;e* + €ze²* +2¢3xe* ;…

A: It is required to solve given equation

Q: QUESTION 2 In Figure 2, the shaft is made of a solid A992 steel at section AB (rs = 25 mm),…

A:

Q: The rigid arm of negligible weight shown in the figure supports a load of F = 852 N. The chains are…

A: Given data: F=852 Nx1=5 mx2=4 my=7 mz=5 m Need to determine the Magnitude of the force in FBE.

Q: 1. A building exhaust fan for a large commercial bullding weighs 180 pounds and operates at a speed…

A: VIBRATION ISOLATORS A vibration isolator is a flexible component interfacing gear and establishment…

Q: What is the radix component for the integer -35

A: This is a really useful lesson that starts with a standard programming language environment for…

Q: Question 2. la0 mm diameter siphon draws water from the reservoir. Considering that the elevation…

A: Given diameter =4mm=0.004 m h(1)=1m h(2)=1 m

Q: use matrix to find solution for omega 3. find vD not in i+j form please.

A: PROBLEM has been solved and student has sought for matrix notation and magnitude wise solution of…

Q: 2-23. A rigid bar AB is weightless and pivots at A as shown in the accompanying figure. Determine…

A: It is asked to generate differential equation of motion and then find the natural frequceny

Q: -D The above diagram represents which type of layout? Hybrid Layout Product layout Process Layout…

A:

Q: a) Ignoring the self-weight of the members, determine the support reactions.

A: we have to evaluate the reaction forces at A & D

Q: Given: N1 = 10, N2 = 20, N3 = 30, N4 = 40 J1 = 1, J2 = 2, J3 = 3, J4 = 4, J5 = 5, D1 = 1, and D2 = 2…

A: θ1sT1s

Q: please send handwritten solution Q4 part e

A:

Q: Consider a four bar linkage with the following links: L0 = 180mm, L1 = 40mm, L2 = 170 mm. Using…

A:

Q: Locate all the centros from the 6 bar linkage shown below. Show the centro polygon step by step and…

A:

Q: Use rotation about the fixed frame to calculate the transformation matrix for a rotation of 30°…

A: For solution refer below images.

Q: Determine the force in each member of the loaded truss. All triangles are equilateral with side…

A:

Q: Compute the position and orientation of the tool point P from the given D-H table for the…

A: Given: Let us consider the given table with values, and the general transformation matrix,…

Q: Q3: Two smooth balls A and B each have a mass of (350 g). If ball A strikes ball B with a velocity…

A:

Q: Solve and Draw the following. [Tech pen (0.2 light, 0.4 medium, 0.6 above heavy)] Consider a four…

A: given; L0=180mmL1=40mmL2=170mmL3=?                                (using grasoph…

Q: Using 2 graphical methods, parallelogram method at polygon method, solve for the value of the…

A:

Q: 2.5 m

A:

Q: 6) An object falls a distance h from rest. If it travels 0.50h in the last 1.00 s, find (a) the time…

A: Given Datas=0.5hg=9.81 m/s2

Q: 3 Th To = 293 K V Room temperature T. emperature changes from Th to T during process 3. The cartoon…

A:

Q: The equipment room housing the compressor and condenser of a refrigerant ammonia system has…

A: Given:-  Room Size = 5 x 4 x 3 m, Refrigerant Ammonia, P=1atm=101.325Kpa, Toxic concentration for a…

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.