For the dual-wheel carrying assembly shown in the figure, P is the load on each wheel, a is the radius of the contact area of the wheel, s is the spacing between the wheels, and d is the clear distance between the wheels. Assuming that the ground is an elastic, homogeneous, and isotropic half space, the ratio of Equivalent Single Wheel Load (ESWL) at depth z = d/2 to the ESWL at depth z 2s is (round off to one decimal place) (Consider the influence angle to be 45° for the linear dispersion of stress with depth) P. 24 2a

For the dual-wheel carrying assembly shown in the figure, P is the load on each wheel, a is the radius of the contact area of the wheel, s is the spacing between the wheels, and d is the clear distance between the wheels. Assuming that the ground is an elastic, homogeneous, and isotropic half space, the ratio of Equivalent Single Wheel Load (ESWL) at depth z = d/2 to the ESWL at depth z 2s is (round off to one decimal place) (Consider the influence angle to be 45° for the linear dispersion of stress with depth) P. 24 2a

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a 3 m long cantilever beam (i.e., a beam fixed at one end) that carries a 500 kg concentrated point load at the free end. Calculate the maximum tensile stress in the beam for the beam section dimensions shown below (Assume solid and homogeneous material; use g = 9.81 m/s2) give answer in N/m^2
A cylindrical bar of 600mm length is subjected to a tensile load of 80 kN along the axis. G = 80 GPa. The change in volume of the cylinder is 72 mm³. The poisson's ratio of the cylinder material is
For the loading situation given in the figure; a) Find the principal axes of inertia and show them on the cross- section. b) Calculate the greatest draft stress occurring on the beam. 图 150 mm 100 mm 50 mm 50 mm
A solid circular rod is subjected to an axial load of P = 310 kN. The diameter of the rod is d = 45 mm, and its length is L = 810 mm. After load Pis applied, the elongation of the rod is ö = 4.3 mm, and its diameter becomes d' = 44.971 mm. Determine (a) the modulus of elasticity for the material. (b) Poisson's ratio for the material. P. Answer: GPa (a) E = i (b) v = i
A beam has a bending moment of 3.5 kN-m applied to a section with a hollow circular cross-section of external diameter 3.5 cm and internal diameter 2.4 cm The modulus of elasticity for the material is 210 x 109 N/m². Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.7 cm from the neutral axis Solution: (i) The moment of inertia = ii) The radius of curvature is (iii) The maximum bending stress is iv) The bending stress at the point 0.7 cm from the neutral axis is
A beam is subjected to a negative bending moment of 20 kN-m. The cross-sectional dimensions of the beam are shown in Figure. 120 mm 40 mm 320 mm 240 mm K 40 mm 265 mm Determine the maximum bending stress produced in the cross section. Include negative sign if compression (in MPa.). 40 mm N.A. H
Student A B D H Number 201780130 2 1 7 8 1 3 Evaluate the following variables and use them as given in the following problems. 200 if I is even, 250 if I is odd (D + G)*10 (H + I/2, if in case the result is zero, use 3 (A +C + E)*2 (P + M)*20 H + 5 M Q %3D 50(E + G + 1) II II || || || |||| ZNPORX
Asap
Question- A circular shaft of diameter 'D' is made of a material for which Young's Modulus of Elasticity is 'E' and Poisson's Ratio is 'v'. The ratio of flexural rigidity to torsional rigidity for the shaft is..
For the beam shown below, b = 6 in and h = 14 in. If the beam is subjected to a transverse shear for of V = 8 kip, determine the largest shearing stress in the beam. Express your answer in psi to the nearest whole psi
Mention correct options with solution
Qus