For the design of the 5-Story building. select the reinforcing needed for the short square tied column shown for the following dead and live loads respectively: PD = 445 kN, PL = 890 kN MDX = 68 kN-m, MLX = 149 kN-m, MDY = 178 kN-m, MLY = 400 kN-m. Material properties: f'c = 27 MPa, and fy = 413.70 MPa. Important: Include the interaction diagram labeled with the derived point of the steel ratio. 400 mm 550 mm 400 mm 550 mm

For the design of the 5-Story building. select the reinforcing needed for the short square tied column shown for the following dead and live loads respectively: PD = 445 kN, PL = 890 kN MDX = 68 kN-m, MLX = 149 kN-m, MDY = 178 kN-m, MLY = 400 kN-m. Material properties: f'c = 27 MPa, and fy = 413.70 MPa. Important: Include the interaction diagram labeled with the derived point of the steel ratio. 400 mm 550 mm 400 mm 550 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

solve the wind load on the left side
Complete answer
SITUATION A: The floor system shown has the following applied loads. Super Imposed Dead Load = 2.00 kPa Live Load = 1.90 kPa Slab Thickness = 100.00 mm Weight of Concrete = 24 kN/m3 Self-Weight of the beam = 1.92 kN/m Material Specifications: f’c = 21.00 MPa fy = 345.00 MPa Steel Cover = 50.00 mm What is the maximum positive moment of beam BE, acting on the midspan? in kN-m What is the maximum steel ratio of the section located at the supports? What is the actual steel ratio of the beam section at the supports? What is the ultimate moment capacity of the beam at the supports? in kN-m What is the effective flange width at the midspan? in mm What is the height of the compression block of the section at midspan? in mm What is the ultimate moment capacity of the beam at the midspan? in kN-m What would be the height of the CHB that can be placed on beam BE? Assuming the weight of the blocks is 2.30 kN/m per meter height? in meters
I need the carrect answer as soon as possible please
Top tie 4. Assume that the wet concrete (s.w. = 150 Ibf/ft3) behaves as a liquid. Determine the force per unit foot of length exerted on the forms. If the forms are held in place as shown, with the ties between vertical braces spaced every 2 ft, what force is exerted on the bottom tie? Brace Form 9 ft Concrete Bottom tie
For the following reinforcement determine the force in the elements DG, DF and EF (section method).
Topic: Restrained Beams 140KN 2.5m 3.5m 5KN/m 3.2m МА 6m MB 11WL2 Pab² 5WL2 Pa?b MA = - MB = - 192 L2 192 L2 INSTRUCTION: 1. Determine the maximum stress in the timber beam with the size of 120 x 370mm.
A TIMBER BLOCK “B x B” mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A “B” mm AND ‘t’ mm THICK STEEL PLATES. DETERMINE THE THICKNESS ‘t’ SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY.
Design a singly reinforced beam. Use f'c = 28 MPa, fy = 414 MPa
Use USD method.
B4