For the circuit shown in the given figure, V = 190 / 0° V. Determine the load impedance ZL for maximum power transfer (to ZL). Calculate the maximum power absorbed by the load. j2Q2 492 www -j3 Q ZL 592 The load impedance ZL for maximum power transfer is 823.3 The maximum power absorbed by the load is 0.1321 kW. + 864.2 mQ.

Q: Suppose you have measured a time delay of 70 microseconds between the two cursors below. The signals…

A: In this question We need to determine the angle between both signals in degree.  We know Frequency…

Q: The main difference between a register and a counter is

A: ans:(d) register has no specific sequence of states

Q: Consider a 8-bit ADC and full scale voltage measurement range of (-29 to 29).The Resolution  will be…

A:

Q: 2. Determine the reaction at the supports using E= 70 GPa and I = 1,300,000,000 mm^4. Draw the FBD…

A: A free-body diagram is a visual, dematerialized, symbolic depiction of the body (structure, element,…

Q: 11. What is the count range of the Asynchronous counter shown below? T 12. CLK 30 30 SCLE 74LS76N…

A: Given counter is Asynchronous Counter because clk is given first flipflop and then output of first…

Q: Show all the base-10 digits 0-9 on a 7 segment display.

A: The solid state optic PN junction diode known as an LED, or light-emitting diode, produces light…

Q: Draw and label the block diagram of the instrumentation calibration chain.

A: Instrument calibration- Calibrating an instrument is to ensure that the instrument is working…

Q: multiplexer contains. multiplexer contains.... select lines 4-1 4 O 20 8 O select lines 16-1 4 O 8 5…

A: In this question we need to choose a correct option

Q: Q what is clocking block and intial block

A: Final block is executed after $finish. Final block doesn't have delay statement.Module is a block a…

Q: OLU The state diagram for a negative edge triggered counter is chown below. Sketch the corresponding…

A: Since the counter is counting to the number 15, the required number of the flip-flop will be four to…

Q: art 4. Two Bit Wide 4 x 1 Multiplexer sing process INPUT_A INPUT_B OUTPUT_Y INPUT_C INPUT_D…

A:

Q: 6- What is the difference between Software and Hardware interrupts?

A: Difference between Software and Hardware interrupts ?

Q: 2. Identify each device. (a) 74LS157 (ь) 74LS151

A: According to the context of the given question, it is only required to identify the given ICs in the…

Q: Calculate circular convolution of first 4 digit and lasr 4 digit of your student number. My student…

A: circular convolution ofxn=2,0,9,1 first 4 digitshn=6,0,7,5 last 4 digitsyn=xn⊕hn

Q: Do Y. So EN Parity generator Demultiplexer Decodor 身

A:

Q: Please answer in typing format

A: The information provided is not sufficient to definitively determine the value of TC. Here's why:…

Q: need to convert the drawing from a handwritten drawing to a typeface on the computer, please OPEN…

A: Given circuit:

Q: The carrier signal is always an analog signal. an analog signal in case of an analog information…

A:

Q: A conveyor motor has a N.O. START button (I:0/3) and a N.C. STOP button (I:0/4) to start and run the…

A: To draw the program rungs for given operation

Q: Choose the correct instruction that will send data to an I/O device. IN AL, 60 IN 60, AL OUT 60, AL…

A: Format of Instruction: Opcode Operand1, Operand2. Opcode tells about the what kind of task is to be…

Q: One method for turning off an SCR is called forced commutation * TRUE False

A: SCR: SCR is commonly known as Silicon controlled Rectifier. It has four junctions. SCR is turned on…

Q: The regiater length is 4 bits and initially it contains 1001. Shift the register to the right six…

A:

Q: The following circuit is a Modulus 14 counter. If we disconnect the input connection to the AND gate…

A: Right Answer option 11

Q: Part a) Two clock technologies used in microcontrollers are the crystal oscillator and the RC…

A: Microcontroller required a clock pulse for healthy (without any error) operation. Clock pulse helps…

Q: For a 10-bit digital ramp ADC using 500 kHz clock, the maximum conversion time is 1. 2048 μsec 2.…

A: Number of bits n=10, Frequency of the clock f=500 kHz.

Q: (c) The modulus of a counter is the number of unique states through which the counter will sequence.…

A:

Q: Draw communication block digram, and exlpain each element.

A: Communication-  Communication is a process in which the information is transmitted from one point to…

Q: 3- Perform the deconvolution operation between the following two signals:

A: Deconvolution operation of given two signals;

Q: 8. We have two push buttons A and B. Design a 3-digit BCD counter that: - counts from 000 to 999 if…

A: The objective of this question is to design a 3-digit BCD (Binary Coded Decimal) counter with…

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.