For the circuit shown in figure, potential difference of 12 V is applied across AB C 20 E 30 20 20 Lwww wwwwww 32 D 20 F 12 12 V Current drawn through cell is A. O M-Vl=3 V more than 1 correct. i will give full rating.

Q: difference between measurement uncertanty and measurement error

A: Given : Need to find the difference between measurement error and uncertainty.

Q: it is called as the difference between the value and the measured value of a quantity a. mistakes b.…

A: In this value we will find significant figures...

Q: What is the advantage and disadvantages Static and Dynamic characteristic of measuring instruments.…

A: Step-1->Static and dynamic characteristics are two important aspects of measuring instruments.…

Q: hich of the following can’t be included in data required for coordination study? A)X/R ratio B)MVA…

A: characteristic curves of the fuses and breakers are generally analyzed in the coordination study

Q: In a rectifier circuit , DC output voltage and RMS output voltage is  0.3 V & 0.48 V respectively.…

A: Form factor is ratio of root mean mean square to average value of output voltage of rectifier. Form…

Q: What can you say about the topic: PHILIPPINE ELECTRICAL CODE 1

A:

Q: emts 8₁ = 19.9 V. 8₂-10.7 V, and 83-5.40 V, and the resistances are each 2.000. What are the (a)…

A:

Q: Khee Voltage of Ilicon semi nductor. (without Your answer A condition where zero (0) volt is less…

A: 1) Knee voltage of silicon semiconductor is 0.7

Q: 2-T Plip.flop to D Plip.Plop ConverSion.

A:

Q: & Prove That %3D

A: Resonance Resonance is the condition when the voltage across a circuit becomes in phase with the…

Q: 1. WRITE THE CKT. DIAGRAM OE FOUR BASIC TYPES OF SERIES CKT.

A: Series circuit A Series Circuit occurs when two or more loads are linked in series. If one load or…

Q: In FET, what is the value for when Ip=lpss/2? [Approximate time to answer: 2 Minutes.] O gmo/2 O 3…

A: solve for transconductance

Q: recall the topcis of the electronic Device and circuits

A: There are many topics in EDC  These topics are  1- Semiconductor diode  2-Diode circuit

Q: In static characteristics, is defined as the difference between the true value applied to a…

A: in static characteristics, Accuracy is defined as the difference between the true value applied to a…

Q: What is the percentage of carbon residue? What is the importance of carbon residue?

A: 1) The carbon Residue value of fuel depends on the refinery processes employed in its manufacture.…

Q: Q2. What are the major carriers in the depletion region? Explain.

A: Here i have described it.

Q: Explain ethics in your own words in the engineering field.

A: Engineering ethics is defined as the field of applied ethics anda system of moral principles that is…

Q: Given the information appearing in Figure beside (assume Ic=IE) determine: (a) Ic. (b) VE. 18 V (c)…

A: Disclaimer:  Since you have asked multipart questions, we will solve the first three subpart for…

Q: The AND-OR implementation of PAL is having O a. Programmable AND array and Programmable OR array Ob.…

A: Given: Brief description: In the above given question they are discussing about the working of the…

Q: In a rectifier circuit , DC output voltage and RMS output voltage is  0.3 V & 0.6 V respectively.…

A:

Q: +V1ev1- L3 13/23 R2 v5 es V4 e4 |12/02 Figure 2060

A:

Q: Difference in the digital and the analog systems

A: Both digital and the analog systems are used to transmit and received information (or signals). The…

Q: IEEE and IEC standards

A: standards for electrical safetyIEC - international electrotechnical commissionIEEE - institute of…

Q: Q2: (A)Find the following: 1- (110)10+ (0111)2.by using BCD numbers. 3-(3E91)16- (1F93)16by using…

A: The number system is used to represent information in digital electronics. Different bases exist in…

Q: tronic components definitions and si units and color coding

A: Electronic components : There are mainly two type of Electronic components one is active Electronic…

Q: A transistor is used as a switch and the waveforms are shown below. The parameters are given as…

A: Given  Transistor as switch and waveforms as shown  Vcc=200 vVCE(sat)=1 vICS=100 AICEO=1 mArise time…

Q: Briefly describe how a distance can be measured by the method of phase comparison

A: From the method of phase comparison, the distance is measured indirectly by determining the number…

Q: Define Analog

A: Analog can be defined as the signal, which is continuous. The analog signal has a time-varying…

Q: Identify each characteristic curve by the type of FET that it represents. Ip -VGS +VGs

A: For N channel JFET, the VGS voltage is negative and the saturation current IDs we obtain at Vgs.

Q: Find the decimal equivalent of the binary number (1011.011)2

A: Binary numbers are those numbers which have 2 in their base and decimal numbers are those numbers…

Q: Q1. Convert following numbers in given radix system: a. (173)10 into hexadecimal b. (2E3)16 into…

A:

Q: Experiment Title SIGNAL GENERATORS

A: WE have to discuss signal generator, The sine wave generator represents the largest single category…

Q: The neutral current is equal to three times of ....... sequence current.

A: Current in nautral is sum of three phase currents. Current in each phase is sum of possitive…

Q: From the table, what is the circular mils for the following: a. 14 AWG a. 10 AWG b. 30 AWG c. 20 AWG

A:

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.