For the circuit shown in Figure B24i.Draw the DC load line in the Graph B24ii.Calculate the Q point if the zero signal base current is 55 µA and a = 0.95IcVCER12ΚΩNo SignalVcc20 VFigure B24 For the circuit shown in Figure B23, a = 0.97,%3Dcalculate the following:i.Collector current (Ic)ii.Collector-Base voltage (VCB)iii.Emitter Current (IE)iv.Base Current (IB)IEIc2.5 kOuiput2.8VIB10VVEEVccFigure B23

Draw the dc load line of the circuit. Find the Q point if the base current is given. as per…

For the circuit shown in Figure B24 i. Draw the DC load line in the Graph B24 ii. Calculate the Q point if the zero signal base current is 55 µA and a = 0.95 Ic Is t VCE R1 2ΚΩ No Signal VBB Vcc 20 V Figure B24

For the circuit shown in Figure B24 i. Draw the DC load line in the Graph B24 ii. Calculate the Q point if the zero signal base current is 55 µA and a = 0.95 Ic Is t VCE R1 2ΚΩ No Signal VBB Vcc 20 V Figure B24

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 60 Hz sinusoidal voltage with an RMS value of 120 V is applied to a single-phase full-wave SCR rectifier. The DC output voltage of the rectifier is 101 V, the firing angle (in degrees) of SCR is would be: O A. 36 O B. 45 O C. None of the other choices are correct O D. 30 O E. 60
a/Draw the output voltage waveform for the bridge rectifier in this figure : Da 120 V ms B/ What PIV rating is required for the diodes in a bridge rectifier that produces an average output voltage of S0 V? ellee
A 120 Vp is applied to the primary coil of a center-tap transformer of turn ratio (n1 : n2 = 6: 2) . If the secondary coils are connected to a Ge diodes center-tap full wave rectifier, the output DC voltage is about __________. *1- 13.42 V2- 14.15 V3- 15.58 V4-12.54 V5- 16.23 V
3. Design a four-resistor BJT bias circuit, similar to the one shown in Figure 2, such that V3 = 4 V and Ic = 1 mA. Assume VBE (on) = 0.7 V and B-150 for the transistor. 12V R1 R2 10k RC 5.6k Q2N2222 RE Figure 2 Note: Use PN2222A in Multisim
Q1/ Sketch and describe mathematically the even and odd components of the signal shown in Figure (1) -1-2-012345 Figure (1)
A full-wave bridge rectifier is to be designed to produce a peak output voltage of 10 V, deliver 100 mA to the load, and produce an output with a ripple of not more than 7.5 percent. Assume that the frequency of the source is 50 Hz, and that a constant drop voltage model with Vp = 0.7 V is t of used. D1 D2 vs(1) RL vz(?) D3 D4 Source Rectifier Load a) Calculate the needed value of the load resistor R1. 1 b) Calculate the peak value of the voltage source which should be used V (t). [ c) What will be the value of the ripple voltage V7 [ d) Calculate the value of the required capacitor C. [ e) Explain in your own words the difference between the output with and without using the capacitor in the circuit above.
A single-phase half-wave controlled rectifier connected to 120V, SOHZ supply to feed load resistor 5a. If the fire angle (a) adjusted to give the maximum output for the rectifier. Calculate and draw the following: a DC Power b- AC Power e- The rectification eli ency d- Draw the signals (VS, Pulses, V output and VT). single-phase half-wave
3. For the half-wave rectifier given in the figure below, find the average values of the output voltage and current, and the ripple factor of the output voltage. D1 Io Dbreak R1 1k vo VAMPL = 169.71 FREQ = 50
Figure B23 Q24. For the circuit shown in Figure B24a, Ve-15V Rc= 2k2 Rs = 20k2 VBB-3V Figure B24a i) Sketch the DC load line in the Graph B24 ii) Calculate the Q point, if the zero signal base current is 60 µA and a = 0.98. Mark the Q point in load line. Page 5 of 6 LG
Calculate the following a) V1 [1 b) i c) i2 Q17 The half wave rectifier is supplied with 230V, 70HZ signal. Assume the number of turns in the primary to secondary ratio is 7:2. i) Calculate the average de current through the load resistor 3KQ. Calculate the value of input ac power, output de power. 18. For the circuit shown in Figure B18, Vcc = 18 V, B = 110, Rc = 4.7 kQ and RB that VBE=0.7 V. 450 k2, assum %3! Vcc | Ic Ro RB Vc VCE
Q4. For the three-phase fully-controlled bridge rectifier circuit shown with purely resistive load: a = 90° a. Sketch the output voltage waveform. a b. Determine the ripple factor. VA= 240 V RL 752 CB A-B A-C B-C B-A CA C-B a Vc 27
Q3: bridge rectifier circuit shown in Figure (1), with a forward diode resistance Rd=12, and Rd=0 for a reverse bias. The input voltage of the circuit is 240V and 482 load resistance. Determine: The de load current, the power input efficiency and the PIV rating is required for the diodes. D4 D1 Rd=10 RL=480 Vs Vrms D3 D2 Figure 1