For the circuit shown in Figure 1. v+ = 12 V ERC2 3D4 k2 Rc= 8 k2 Rc=8 k2 12 k2 = 200 B1 =200 vo2 B2, Q3 = 200 Q2 O v2 RE = 3.3 ko ro = 100 kN Qs Q4 V- =-12 V Find Figure 1 a) Find the magnitude of I, b) Find the differential mode gain A c) Find the common mode rejection ration in dB d) If a 30 mV input signal is applied to the input of terminal v, and v, = 0, what will be the output signal? %3D ww

For the circuit shown in Figure 1. v+ = 12 V ERC2 3D4 k2 Rc= 8 k2 Rc=8 k2 12 k2 = 200 B1 =200 vo2 B2, Q3 = 200 Q2 O v2 RE = 3.3 ko ro = 100 kN Qs Q4 V- =-12 V Find Figure 1 a) Find the magnitude of I, b) Find the differential mode gain A c) Find the common mode rejection ration in dB d) If a 30 mV input signal is applied to the input of terminal v, and v, = 0, what will be the output signal? %3D ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The - amplifier configuration has the highest input resistance compared to the other configurations CB CE CC a & c Vindows bui StV A Moving to another question will save this response Bb F12 PrSc Pause F9 F10 F11 F7 F8 SysRq 0000
Show the output waveforms of a positive and a negative clipper circuit with series and shunt connections.
For the following amplifier small signal equivalent circuit, Ro is Rsi O b. ww Select one: O a. infinity ro R₁ R₂ Vgs +8mVgs www O c. none of the answers O d. RD D R₂ Rp Vds
VDD VDD = 5V Ro RD = 3K R1 = 210K Rin RD R2 = 100K R1 RL = 10K oVo VTN = 0.75 Cc1 KN = 0.9 A = 0 RL Vin (+ R2 Find IDQ VDSQ Small-Signal gm ro Draw small-signal eq. circuit Find Av, Rin, Ro
why the frequency fT is called the ? unity gain frequency
The midrange voltage gain of a certain RC coupled amplifier is 150 and the dominant critical frequency of the amplifier at the low frequency region is IkHz and the critical high frequency is 1MHz. Determine the voltage gain (in dB) at the following frequencies: 100 Hz, 200 Hz, 1 kHz, 10 kHz, and 1 MHz
Which of the following statement is true? Conjugate matching guarantees the maximum output power regardless of input power. The optimum source impedance for the minimum noise figure can be obtained by conjugate matching condition. O The first stage is the most important to minimize the overall noise figure in cascaded blocks An oscillator cannot be built with a single stage amplifier. None of the above
Q2 Calculate the voltage gain, output voltage, input impedance, and output impedance for the cascade amplifier of Figure. Ipss V, = -5 B = 450 = 18 +20 V 22 k2 0.5 uF 2.4 k 15 kQ 0.5uF ImV pss 0.05 uF 4.7 ka 3.3 M0 680 0 # 100 uF = 100 uF
The circuit in Figure 1 represents the circuit model of an interference path from source vin to the 10 MQ load resistance at vout- C1 C2 1 pF 1000 pF R V in out 10 MQ Figure 1. Interference modeling a) Determine the transfer function H(f) = vou/Vin from vin to vout- b) Determine the output magnitude vout when Vin is a 170V pk sine wave at 60HZ c) Determine the output magnitude vou when vin is a 1V pk sine wave at 1 MHz
Problem • Determine the input and output impedances of the given amplifier. The op-amp datasheet gives: Zin = 2 Mohm, Zout = 75 ohm, A = 200000. 4 Find the Closed-loop voltage gain. www R OV 220 ΚΩ R₁ 10 ΚΩ out
VCC R2 RC- RI RL R1 RE VEE Assume: B=100, VA=150, Vcc=12V, VEE=GND, Rr=2K, R1=160K, R2=300K, RE=3K, Rc=2.2K, and R1=100K. Convert the circuit to a common-collector circuit. Draw the new circuit (assume the same values for the input and load resistances). Then compute the terminal voltage gain, and Rin (for the whole circuit), re-computing any parameters that you need to solve.
Analog Electronic: Frequency Response of BJT and FET Amplifier