For the circuit shown below and V = 12.14 V, what is the voltage, in Volts, across the lead resistor (the first one following the voltage source) after a very long time? The resistance and capacitance values have an infinite number of significant figures. Do not enter units with your answer. RC Circuit 2.PNG 10 1Ω 1Ω x(t) V y(t) C=1.5 F

For the circuit shown below and V = 12.14 V, what is the voltage, in Volts, across the lead resistor (the first one following the voltage source) after a very long time? The resistance and capacitance values have an infinite number of significant figures. Do not enter units with your answer. RC Circuit 2.PNG 10 1Ω 1Ω x(t) V y(t) C=1.5 F

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 22P: An automobile starter motor has an equivalent resistance of 0.0500 and is supplied by a 12.0-V...

See similar textbooks

Similar questions

Consider the circuit shown in Figure P28.21 on page 860. (a) Find the voltage across the 3.00-0 resistor, (b) Find the current in the 3.00-12 resistor.
Why is the following situation impossible? A technician is testing a circuit that contains a resistance R. He realizes that a better design for the circuit would include a resistance 73R rather than R. He has three additional resistors, each with resistance R. By combining these additional resistors in a certain combination that is then placed in series with the original resistor, he achieves the desired resistance.
An uncharged series RC circuit is to be connected across a battery. For each of the following changes, determine whether the time for the capacitor to reach 90% of its final charge would increase, decrease, or remain unchanged. Indicate your answers with I, D, or U, respectively. (a) The RC time constant is doubled. (b) The battery voltage is doubled. (c) A second resistor is added in series with the original resistor.
A 1,00-?O voltmeter is placed in parallel with a 75.0kresistor in a circuit, (a) Draw a circuit diagram of the connection, (b) What is the resistance of the combination? If the voltage across the combination is kept the same as it was across the 75.0-kresistor alone, what is the percent increase in current? (d) If the current through the combination is kept the same as it was through the 75.0-kresistor alone, what is the percentage decrease in voltage? (e) Are the changes found in parts (c) and (d) significant? Discuss.
A battery has an emf of 15.0 V. The terminal voltage of the battery is 11.6 V when it is delivering 20.0 W of power to an external load resistor R. (a) What is the value of R? (b) What is the internal resistance of the battery?
A homemade capacitor is constructed of 2 sheets of aluminum foil with an area of 2.00 square meters, separated by paper, 0.05 mm thick, of the same area and a dielectric constant of 3.7. The homemade capacitor is connected in series with a 100,00- resistor, a switch, and a 6.00-V voltage source, (a) What is the RC time constant of the circuit? (b) What is the initial current through the circuit, when the switch is closed? (c) How long does it take the current to reach one third of its initial value?
The circuit shown in Figure P27.17 is connected for 2.00 min. (a) Determine the current in each branch of the circuit. (b) Find the energy delivered by each battery. (c) Find the energy delivered to each resistor. (d) Identify the type of energy storage transformation that occurs in the operation of the circuit. (e) Find the total amount of energy transformed into internal energy in the resistors.
Three 100- resistors are connected as shown in Figure P21.41 The maximum power that can safely be delivered to any one resistor is 25.0 W. (a) What is the maximum potential difference that can be applied to the terminals a and b? (b) For the voltage determined in part (a), what is the power delivered to each resistor? (c) What is the total power delivered to the combination of resistors?
Choose the words that make each statement correct. (i) When two or more resistors are connected in series, the equivalent resistance is always [(a) greater than; (b) less than] any individual resistance. (ii) When two or more resistors are connected in parallel, the equivalent resistance is always [(c) greater than; (d) less than] any individual resistance.
An automobile starter motor has an equivalent resistance of 0.0500 and is supplied by a 12.0-V battery with a 0.0100- internal resistance, (a) What is thecurrent to the motor? (b) What voltage is applied to it? (c) What power is supplied to the motor? (d) Repeat these calculations for when the battery connections are corroded and add 0.0900 to the circuit. (Significant problems are caused by even small amounts of unwanted resistance in low-voltage, high-current applications.)
When resistors with different resistances are connected in parallel, which of the following must be the same for each resistor? Choose all correct answers, (a) potential difference (b) current (c) power delivered (d) charge entering each resistor in a given time interval (e) none of those answers
Figure P18.26 shows a voltage divider, a circuit used to obtain a desired voltage Vout from a source voltage . Determine the required value of R2 if = 5.00 V, Vout = 1.50 V and R1 = 1.00 103 (Hint: Use Kirchhoff's loop rule, substituting Vout = IR2, to find the current. Then solve Ohms law for R2. Figure P18.26