a-Фт0.002 m1Area =2 x 104 m?2V =200 turnsArea for sections other than bg = 5 × 104 m?lab = log = lgh = Ina = 0.2 mIbe = ! = 0.1 m, led = leg = 0.099 m%3DFor the cireuit magnetic eircuit above find the value of I required to establish a flux in the gap of9x 10*wb. And the material of the core is cast iron. N = 200 turns. b.Cast steelФThe figure shows a core with mean path length of 40cm. There is a small air gap of 0.05cm in thestructure. The cross sectional area of the core is 19 cm?.Assume that fringing in the air gap increases the effective cross sectional area of air gapby 5%. The no of turns is 400. Given this information. Finda) The total reluctance of the flux path (cast steel plus air gap)b) The current required to produce a flux density of 0.5T in the air gap

We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Answered: For the circuit magnetic circuit above…

For the circuit magnetic circuit above find the value of I required to establish a flux in the gap of 9x 10*Wb. And the material of the core is cast iron. N = 200 turns.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The magnetic structure in the figure below is made of silicon steel. Determine the values of IB required in the winding of the figure below, to produce flux of OB=11mWb, l=0.03mm and NB=500 turns. 6 A B C \g 12 4 dimensions in cm 7 6 15 8 15 6
In the core of a long solenoid the magnetic flux density is 100 Tesla. The cross section of the solenoid is a circle with diameter d=10 cm. Determine the magnetic flux in the core in mWb.
For the magnetic circuit shown in the figure, the iron core with N = 500 turns -Magnetic permeability is 200. its average length is 40 cm -The diameter of the cross-sectional area is 1 cm. Find the current that must pass through the winding to produce 0.5 mWb of flux in a 1mm air-gap magnetic circuit?
Which of the following is the analogous of current in an electrical circuit when it is compared to a magnetic circuit? Reluctance Magnetomotive force Magnetic flux Permeability
A flux of 0.0016 Wb flows in a silicon sheet steel coil/core. The arrangement appears as shown below with the following dimensions: Ac = 0.0025 m? Core/gap area: Flux path length: le = 0.350 m lg = 0.0015 m N = 500 Air gap length: Number of turns: %3D A. What is the current, I, through the winding? B. What is the energy stored in the inductance? C. Assume that the current is given by i =9.75 sin (3147) A. What is the RMS voltage that would appear across the winding? D. Assume that the gap is removed from the arrangement with the flux path remaining at 0.350 m. For a flux of 0.0016 Wb, what is the inductance of the arrangement? E. What is the energy stored in the inductance with the gap removed?
An iron circuit with a small0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm2, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (u, = 800 for iron). Figure 1
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm?, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (4, = 800 for iron). Figure 1
An iron core has a cross-sectional area of 10-3 square meter and mean circumference of 1 meter. The relative permeability of the material is 500 and the number of turns is 200. Determine the current required to set up a flux of0.001 weber. 7.54 A b. 7.96 A c. 8.19 A d. 8.47 A a.
In the magnetic circuit shown below, what is the flux density produced if the relative permeability of the core material under the given condition is 1000? 5 A-> 100 turns R = 5 cm
A magnetic ring has a mean circumference of 20 cm and a cross-section of 20 cm² and has 800 numbers of turns of wire. When the exciting current is 5 A, the flux is 2 mWb. The relative permeability of iron is nearly
Help me with this please in text not handwritten and pl pls pls fast sir
Q2. Determine the current Ii required to establish a flux of o -4 x 10 Wb in the magnetic circuit of figure below, draw the equivalent circuit and find the circuit inductance given (4. - 2800 H/m). Lg - 0.2 cm Sheet Steel I I-0.28 A N2 - 200 turns A- 1.6 x 10+ m' N - 40 turns Labed - 20 cm