For the beams shown in Figure 2.2, find the internal forces and moments as a function of the length x along the beam (as shown in the figures) at the segments indicated by the dotted lines. Sketch these results as a function of x by hand. What do you observe? How are the functions from each segment related to those in the previous one? x L 45% L/2 B (a) B 2P L2 L/4 CP L/4 C D

For the beams shown in Figure 2.2, find the internal forces and moments as a function of the length x along the beam (as shown in the figures) at the segments indicated by the dotted lines. Sketch these results as a function of x by hand. What do you observe? How are the functions from each segment related to those in the previous one? x L 45% L/2 B (a) B 2P L2 L/4 CP L/4 C D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam is loaded with a system of forces, as shown in the figure. Calculate the resulting pair of the system and express it in Cartesian coordinates. And after solving it, answer the following questions: a) The moment of the pair of forces of 750 pounds, has the value ofb) The perpendicular distance between the torque of 750 pounds, is equalc) The moment of the torque of 8000 pounds, isd) The Cartesian couple resulting from the force system on the beam is Response
The figure shows a beam with multiple forces acting on it. The X indicates an axis of rotation at the right end of the beam. At this axis, the net torque is found to be 0 Nm and the net force is found to be 0 N. If the axis of rotation were instead at the left end of the beam, the net torque would be α
The figure below shows, at left, a solid wheel of radius R = 0.600 m and mass 60.0 kg. Mounted directly to it and coaxial with it is a pulley with a much smaller mass and a radius of r = 0.230 m. The wheel and pulley assembly are on a frictionless axle. A belt is wrapped around the pulley and connected to an electric motor as shown on the right. The turning motor gives the wheel and pulley a clockwise angular acceleration of 1.67 rad/s. The tension T, in the upper (taut) segment of the belt is 165 N. (a) What is the tension (in N) in the lower (slack) segment of the belt? (b) What If? You replace the belt with a different one (one slightly longer and looser, but still tight enough that it does not sag). You again turn on the motor so that the wheel accelerates clockwise. The upper segment of the belt once again has a tension of 165 N, but now the tension in the lower belt is exactly zero. What is the magnitude of the angular acceleration (in rad/s2)? rad/s = /x*M/L dx, prove that the…
Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution Video. For the shape below, assume the following dimensions: a = 175 mm b = 220 mm d = 300 mm t = 23 mm The centroid of this shape is located 71.762 mm to the right of point H shown in the figure. What is the moment of inertia ly about the y centroidal axis for this shape? H Answer: ly M b 2t mm4
A transmission tower (a truss) for supporting electric wires is shown. The load of wire at N is shown as force Fi at an angle of a and the load of wire at A is shown as force Fz at an angle of B. Using the values given in the table below: Fi (N) F: (N) a (deg) B (deg) w (m) h (m) Value 50 40 45 30 3 5 a) Find the reaction forces at supports Y and Z. b) Determine the forces supported by members NB, NL, SV, and UX and specify whether the member is in Tension or Compression. B U F
Question 3: Open Ended The beam in the following diagram has the following numerical values in stiffness: 77 Stiffness in bending = 1 Stiffness in axial tension = 1 What would the new values of stiffness in bending and axial tension be if the Height of beam is doubled while the Width remains constant? What would the new values of stiffness in bending and axial tension be if the Width of beam is doubled while the Height remains constant?
Calculate the support reactions of the beam and determine the degree of indeterminacy in the figure. q:11
Consider the figure shown below. The radius of gyration of the circular area with respect to the line x is; 2 m A V5 m (в Vz m B 2 m D)
Answer are nearly around 2237N ,0 N and and 1887N
The cross section of the beam shown in the figure was created by hammering 16x4 [cm.cm] and 24x4 [cm.cm] planks with nails as shown in the figure. (σem = 10 MPa; τem = 1 MPa) Considering the maximum distributed load q that the beam can carry; In which of the following options the inequality regarding the nail spacing is given correctly? Notes:Nails will be spaced evenly.-Each nail can carry a cutting force of 800 N.
Please solve it quickly
For the frame shown below, The mass of the object connected is 60-kg. what is the value of horizontal reaction force at the pin A in N? (Note: enter your numeric answer only. No need to enter units. Give your answer to three decimal places and negative in the left direction). Ax = N -1.2 m 0.1 m 0.3 m B C 0.6 m A