For the beams loaded as shown below: (a) Determine the bending moments at each of the supports (b) Sketch the bending moment diagram indicating significant values (c) Sketch the shear force diagram indicating significant values Question 1 50kN/m 80kN I 31 A 3m В 3m 3m C

Q: Sketch the graph of the cutting moment and bending moment of the structural element below.

A:

Q: P=75KN e=200mm 200 mm 20 mmo 200 mm

A:

Q: The square steel plate has a mass of 1920 kg with mass center at its center G. Calculate the tension…

A:

Q: You have been tasked with designing a beam to support a lifting crane. The applied load is offset…

A: Given: A simply supported member subjected to two point loads of 4kN and 1.5 kN apart from each…

Q: a. In your own words, what is the difference between a positive and a negative bending moment? b.…

A:

Q: A simply supported beam is loaded as shown above. What is maximum bending at point D?

A: A simply supported beam,Subject to an uvl 0 to 20kN/m,Point load of 40kN, and a clockwise moment of…

Q: Q1: The beam shown in Fig1.carries a concentrated load of W and a total distributed load of 8 W.…

A: Given data:

Q: (a) Draw the shear and bending-moment diagrams for the beam and the given loading. (b) Calculating…

A: Free Body Diagram of the given beam: Calculate reactions at fixed support:…

Q: 1)The beam in the figure has a rectangular cross section of dimensions b and h and is subject to…

A: Given  B/h = 0.7  Allowable normal voltage=1400 kgf/cm2

Q: 200 550 A 220 N-m D E 200 F Dimensions in mm determine the magnitude of the pin reaction at D when…

A:

Q: QUESTION 11 Consider the circular bent rod with diameter 20 mm. The free-end of the bend is…

A: Given data  Length  L section. Point loads  Axis system  Diameter

Q: The beam in the figure has a rectangular cross section of dimensions b and h and is subject to when…

A: Allowable normal voltage (ANV) = 1400 kgf/cm2 = 1.4 x 107 kgf/m2 = 1.4 x 104 tf/m2 Ratio of b/h =…

Q: D 40 kN pin-jointed frame C F E HE MA EI EI 2EI 120 kN VE 4.0 m 4.0 m 4.0 m 4.0 m 3.0 m

A:

Q: 5 kip/ft 1 ft 11 ft 30 kip-ft 11 ft Figure P-552 11 in ♫

A:

Q: Using the shear force diagram, what is the shear force at x=15m? approx.____N O -50 O-100 O-125…

A: A cantilever beam:-

Q: 24.7 26.4 21.9

A:

Q: A rigid bar AD is hanged by two steel cables of diameter 0.065 in as shown in the figure. Find: a)…

A:

Q: B. 10 k A |8A| -8 ft- -8 ft 20 k C -8 ft 20 k D -8 ft-

A: Loadings and beam lengths are given. Find : Static indeterminacy and reactions. Draw SFD & BMD.…

Q: Q1/ for the beam shown in figure below detemine Max moment capacity (Mn) 300 mm 535 600 mm mm 3025…

A: Introduction- The beam is a structural component that largely resist loads delivered lateral to the…

Q: Figure Q2a shows a cantilever beam structure, which is fixed at A and roller supported at C. The…

A:

Q: 10km/n 4m em 25KN 5km/m

A: A simply supported beam, of span length 4 m between the simple support and 2 m as a right overhang.…

Q: For the beam shown, what is the value of the shear diagram at the middle of the beam? Select the…

A:

Q: 20 You are not provided the free-body diagram for the beam associated with the internal shear force…

A:

Q: The bending moment value at C for ,4 * the beam shown in fig is 20kN/m D В A 40KN 3m 2m 2m 60 90…

A:

Q: For questions 1 to 5, consider a bent rod fixed at the wall at A and is acted upon by a 20- N force…

A:

Q: F T2 Kim-*-Im-*Im-) 30KN

A: Given data:

Q: Compute y. The interaction diagrams in Appendix A are each drawn for a particular value of the…

A:

Q: 6 mm 12 mm 12 mm b. 60 mm 6 mm 30 mm 100 mm Demne he nd monent of erta of the section in 10

A:

Q: Which of the following best gives the plastic moment capacity of the W410x68, Fy = 345 MPа? bf tf…

A:

Q: At the joint of a steel bridge, preloaded high-strength bolts have been used. Assume that the…

A:

Q: Determine the kind and magnitude of bending stress, in MPa, of the fiber 70mm below the neutral axis…

A:

Q: The I-beam shown below has a length of 6m and it is simply supported at both ends The beam is under…

A:

Q: Problem 4.9 - Member ABD is supported by a pin at A and a cable attached at B and D. The cable…

A:

Q: SUBJECT: Theory of Structure Determine the force in each member of the truss shown by the method of…

A: ## Analyzing the Truss Using the Method of Joints**Understanding the Problem:**We are given a truss…

Q: Determine the shear and moment diagrams of the following beams loaded as shown on short size bond…

A: Given Beam is a Simply Supported beam.  It is loaded with UVL.  we need to calculate,  Reactions,…

Q: The answer on the app is given to me and its wrong please i need the right way to solve the problem

A:

Q: Q1/ for the beam shown in figure below determine Max moment capacity (Mn) and the corresponding load…

A: The diagram given in the question are as follows: