For the beam shown, the magnitude of the distributed load is wo = 10.6 kN/m and the beam lengths are a = 6.3 m and b = 18.9 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. Wo В a

For the beam shown, the magnitude of the distributed load is wo = 10.6 kN/m and the beam lengths are a = 6.3 m and b = 18.9 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. Wo В a

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bending moment capacity of the trapezoidal section given in the figure, the equivalent rectangular stressCalculate with equilibrium equations by accepting the block. C25/S420 d’ = 40 mm
1. A simply supported beam with rectangular cross-section is loaded as shown in the figure. Draw the shear and bending moment diagrams and determine the maximum normal stress due to bending. |15 kN 6 kN/m E A В D 120 mm 0.8 m 2 m
The two sub questions and question g as well :
For the beam shown, the magnitude of the concentrated load is P = 12 kN, the magnitude of the couple is MB = 150 kN·m, and the beam lengths are a = 4.7 m and b = 14.1 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Calculate for the shear force in kN at member ED of the frame shown in figure 1 using Portal Method. Enter absolute value and use 2 decimal places in your solution.
Mechanics of deformable bodies. Two decimal places.
Q.2) (a) Calculate the support reactions of the loaded beam shown below. (b) Write equations for w(x), V(x) and M(x) of the beam using singularity functions. (c) Sketch the shear-force and bending moment diagrams for the beam for the beam using the Graphical method. Label the values of shear-force and bending-moment at all key points. 350 N.m G 0.5 m4 2m 95 N/m, 200 N 250 N.m 80 N/m 2m 300 N 0.5 m
sub-part