For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment diagrams. V=500 lbf, V2 = 49 Ibf/in, V3= 10 in, and V4 = 5 in. v3 Provide values at all key points shown in the given shear-force and bending-moment diagrams, Shear Diagram The reaction force Ro- 745 lbf. The bending moment Mo- 9287.5 A= 745 B= 745 C= 245 3 -9288 The reaction force Ro= 745 lbf. The bending moment Mo- 9287.5 lbf-in. In the shear-force and bending-moment diagrams given, 0 0 0 lbf lbf lbf D= 245 lbf P= B lbf-in Q=-1838 lbf-in R= -613 lbf-in v2 Ibf-in. 0.00 0.00

For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment diagrams. V=500 lbf, V2 = 49 Ibf/in, V3= 10 in, and V4 = 5 in. v3 Provide values at all key points shown in the given shear-force and bending-moment diagrams, Shear Diagram The reaction force Ro- 745 lbf. The bending moment Mo- 9287.5 A= 745 B= 745 C= 245 3 -9288 The reaction force Ro= 745 lbf. The bending moment Mo- 9287.5 lbf-in. In the shear-force and bending-moment diagrams given, 0 0 0 lbf lbf lbf D= 245 lbf P= B lbf-in Q=-1838 lbf-in R= -613 lbf-in v2 Ibf-in. 0.00 0.00

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Figure No. 4 Given q = 100 N/m. L1 = 300mm and L2 = 300 mm

Q: The beam shown in Figure Q.2 consists of a W610 x 140 structural steel wide-flange shape [E= 200…

A: Given:Required:Support reaction and deflection at B due to concentrated load P

Q: A rigid, uniform weightless, horizontal bar is connected to three vertical members P. Q and R as…

A: Given:- A rigid, uniform weightless, horizontal bar is connected to three vertical members P. Q and…

Q: 4. An assembly of three rods is shown in Fig. 4. The rods each have the same 25-mm diameter and…

A: free body diagram at joint A

Q: A C

Q: Determine the reactions & Draw the shear and bonding moment diagrams for the beam shown below. Use…

Q: : Find the resultant force (R) of the two forces shown in Fig. below. F1= 55 N 25 F2= 65 N 35 30

Q: |40 = 10 lb/in. %3D P = 80 lb A B = 40 in. 40 in.

Q: Please solve no 6 and 10 step by step solution

Q: For the beam Shown in Figure 1. Use the data in Table 1. Find the following: I. The reaction at…

A: Solution

Q: A simply supported beam is carrying the following loads: Pm = 85 kN w = 24 kN/m The beam has a…

Q: Determine the member force of the truss shown in Figure Q6 by the force method. 1.5 m 20 kN. +2m 50…

Q: Determine the reactions at the support and draw the final shear force and bending moment diagrams…

A: Using flexibility method of analysis###Determination of Support reactions and calculate of SF ,BM…

Q: ind R = 5 kips. All members of the truss are aluminum [E = 10,000 ksi] pipes with an outside…

Q: Determine the reactions at the supports for the Truss shown in Figure. 35.6 kN 35.6 kN 71.2 kN 71.2…

A: We have to determine the value of reaction at the support for the truss shown.

Q: 20 kN/m 60 kN A E В C D -8 m- -8 m- El = constant E = 70 GPa 1= 800 (106) mm4

A: Given, EI=Constant E=70 GPa I= 800×106 mm4

Q: the rotation

A: Given, A plane frame shown in figure has linear elastic spring at node H.Spring constants are,…

Q: Figure 1 shows a frame that is fixed at E. As indicated in the Figure, the frame is exposed to two…

Q: be neglected. Use the flexibility method to calculate and plot the bending moment diagram for the…

A: Calculation of BMD using flexibility / method of analysis ####

Q: Q.04. Calculate the values and draw the diagrams for Shear Force and Bending Moment for the beam…

Q: For the structure shown in Figure 1, complete the following: A. Calculate the reactions B. Draw…

A: To find reaction,

Q: A propped 6 m long cantilever beam is shown in Figure 3. In addition to a saw-tooth loading as shown…

A: Given clockwise moment is applied at B = 10 KN-m

Q: 15 A. Find the reaction at support A (RA) B. Find the reaction at support C (Rc) C. Draw the shear…

A: Draw FBD:

Q: m is loaded and supported as shown. Determine the components of the reactions at supports A and B.

A: Given:- Moment=750ft-lb Point load=800lb udl=200lb/ft To find:- reactions at A and B

Q: 1 kN I KN 1 kN 1 kN 1 kN 2 m 2m H 2 m G 2m 2 m E

Q: Determine the bending moment (M) in kNm at the point x = 4.5 m from point A for the beam as loaded…

Q: Determine the reactions for the beam in the given figure. When & uniform load is applied, the fixed…

A: E = 30000 Kips/in.2I = 240 in.4Support B settle (∆) = X = 0.2 in. Determine the support reaction of…

Q: The beam shown in Figure Q.2 consists of a W610 x 140 structural steel wide-flange shape [E = 200…

A: The beam shown in Figure Q.2 consists of a W610 × 140 structural steel wide-flange shape [E = 200…

Q: The compound beam shown in Figure 2.1 has an internal hinge at point B. It is fixed (clamped) at…

A: Calculation of support reaction at A

Q: A gusset plate for a bridge truss is shown in the figure. Determine the magnitude and direction of…

Q: 1. Determine the force in member CD, CB, CA, BA and BD of the shown below figure. 9' 12 5200 lb

Q: Learning Goal: To solve for the support reactions of a frame. The frame shown in (Figure 1) is…

A: A and D are hinged supports and at C internal hinge is present. To determine Horizontal reaction…

Q: The frame structure shown in the figure has pin support at B and fixed support at E. When Wo= 2…

Q: Q.5 A non-uniform, rigid jointed frame is fixed at supports A and D as snown in Figure Q.5. where El…

Q: 2k 80 k-ft For the structure shown in Figure 2, complete the following: A. Calculate the reactions…

A: For the sake of solving and drawing the diagrams, let me rotate the Fig.2 by 90 degree. From now on,…

Q: Reactions have been calculated for the beam AB shown in the figure. The shear force at location X…

A: Calculate shear force at 4m from A

Concept explainers

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.

Question

For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment diagrams. V=500 lbf, V2 = 49
Ibf/in, V3 = 10 in, and V4 = 5 in.
Provide values at all key points shown in the given shear-force and bending-moment diagrams,
Shear Diagram
The reaction force Ro- 745 lbf.
The bending moment Mo- 9287.5
A=
745 lbf
B=
745 lbf
C=
245 lbf
D= 245 lbf
P= -9288
Q= -1838
R= -613
B
The reaction force Ro= 745 lbf.
The bending moment Mo= 9287.5 lbf-in.
In the shear-force and bending-moment diagrams given,
lbf in
lbf-in
lbf-in
Ibf-in.
0.00
R
0.00

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: given data

VIEW

Step 2: from equilibrium equation

VIEW

Step 3: continue

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem 1. For the frame shown in the figure, determine (a) Reactions at the supports (b) Axial force, Shear Force and Bending Moment at a point on BC lying at 1m from point B 15 kN 30 kN 10 kN 10 kN 25 kN E 12 kN/m 8 kN B с pin HA Hy F 3.0 m 4.5 m 4.5 m VA 12.0 m 5.0 m 7.0 m
For the beam shown, find the reactions at the supports and plot the shear-force and bending-moment diagrams. V=300 lbf, V2 = 46 lbf/in, V3 = 8 in, and V4-6 in. B v3 V4 Provide values at all key points shown in the given shear-force and bending-moment diagrams. es 0.00 Q D 0.00 P Shear Diagram The reaction force Ro 552 lbf. The bending moment Mo= Ibf.in. In the shear-force and bending-moment diagrams given, in.) R
A rigid, uniform, weightless, horizontal bar is connected to three vertical members P, Q and R as shown in the figure (not drawn to the scale). All three members have identical axial stiffness of 10 kN/mm. The lower end of bars P and R rest on a rigid horizontal surface. When NO load is applied, a gap of 2 mm exists between the lower end of the bar Q and the rigid horizontal surface. When a vertical load W is placed on the horizontal bar in the downward direction, the bar still remains horizontal and gets displaced by 5 mm in the vertically downward direction.
Question 4(a) The uniform bar shown in Figure 4 weighs 428 N. It is supported by a pin at A and a cable that runs around the pulley, D. It is subjected to a uniformly distributed load of 17.7 N/m and 12.5 Nm clockwise moment at E. Beam is in equilibrium position as shown in the Figure. Take a = 0.41 m and b = 2.5 m. Determine the tension in the cable and the reaction force at A, both in Newtons. w N/m 75° A ▼▼ ▼ ▼ 12.5 Nm B E 1 m 0.5 m m b Figure 4 Question 4(b) Find a truss from your neighborhood where you can take a photo safely. It does not have to be taken from the perfect angle and as long as we can see the complete truss that is good enough. One photo would be ideal but upto 3 photos can be used. Include these photos in your solutions for this question and based on these photos draw this 2D truss (exact dimensions are not required) with the supports too. Comment on the possible loads and their locations that may be applied to the truss. Discuss the assumptions that you have to…
Determine the force in member JH and BH for the truss loaded and supported as shown in figure (3). Does the statically indeterminacy of the supports affect your calculation? Why? 4 m 4 m G 4 m F 4 m A 4 m B 4 m C 4 m 60° E (50+b) kN Fig.3. Q3
Please help me solve the question in the diagram below