For the beam shown determine the slope and deflection equations for 0

Q: 5. वि० D 10' F is the orange arrow C 10' B 45* 1000lbs Find FAD, FBC, FCD FAB FAC TH

A:

Q: Name: Q1/ Give the Name of plans in the Image? The anatomical planes www.free-anatomy-quiz.com Q2/…

A: Plane A -Frontal PlanePlane B -MidSagittal Plane Plane C - Transverse Plane

Q: the sketch top, front, and right side isometric below. For the objects shown in sure that your views…

A: According to the details provided in the question we need to draw three projection view of the given…

Q: Consider two infinite parallel plates in length, where the top plate is moving to the right at a…

A:

Q: Q) Find Xc and Ye angle 10 m 20m 25 m

A: The Center of mass is a point where the sum of the moment of the weight of each particle is zero. It…

Q: 127 157 18 11 0) D 24y

A: Let's name the marked lengths in the given figure for calculation purpose.

Q: Question 1 A ramp is made by leaning a track against a few textbooks. A cart Is Set track and rolls…

A:

Q: draw isometric diagram with measurement labels

A:

Q: Our mechanical engineering student and your instructor are at it again, this time with the student…

A: Curve is given and we will revolve it around the y-axis to get the solid body.We will use the method…

Q: Q3 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 2:1. 18…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: 3. Point B is known to be 711.202m from A at a bearing of 96°10'13". When viewed from a point P, the…

A: Given Information, AB = 711.202m   To convert an angle from minutes and seconds to a decimal value,…

Q: Referring to the object in Fig. 10, sketch the front, left, and section view following third angle…

A: (1) Analysis of ProblemTake a close look at the provided figure and understand the object's…

Q: What is the sketch of the right face

A:

Q: Q2: Select physical dimensions and produce engineering parts list You are to select two deep groove…

A: The Answer is below

Q: Shown in the image is a vertical section of a 66 block grid of a gold mine deposit. Each block is…

A: Based on the image presented, which includes varying ore grades ranging from 1.4 g/t to 2.9 g/t in…

Q: H.w find the valume of big below? y side Veiw x R- .R. We need to find the size of the disk as shown…

A: To find: The volume of the figure below: Given: The shape is in shape of torus. Formula used: The…

Q: Q) Draw the following projections for the figure shown with scale 1:1. 1. Front View 2. Side View 3.…

A: Solution:

Q: So 180 200 30 Find F and location 200

A:

Q: Write dimensions of work and please explain neately.

A: Given Data⇒ Work

Q: A hammer is balanced at the point "A", close to the metal part. If this hammer is then cut along the…

A: Consider the diagram shown below for the hammer with the center of masses for each side.

Q: for this question just sketch what it should look like:

A: Note : Window is denoted by point P

Q: P4-2) Answer questions about the following drawing. a) How many linear dimensions? b) How many…

A: As we are entitled to solve upto three subpart. I am solving here the first three parts for You. To…

Q: Joe takes his little brother Andy down the the playground for an afternoon out. Andy would like to…

A: Considering a frictionless seesaw mechanical system. Mechanical Advantage of the system is the ratio…

Q: In a forming process the length of material changes from 50 mm to 60 mm. Show the num true stress…

A: Given lo =50mm l=60 mm K= 210 MPa n=0.27

Q: The M777 lightweight 155 mm howitzer is a piece of artillery whose rounds are ejected from the gun…

A:

Q: 1. average velocity is correct (-0.75 m/s) but instantaneous velocity (-1 m/s) is incorrect can you…

A: Given :    To find : instantaneous velocity v when t =4 s

Q: a) A locomotive is travelling at 35 m/s up an incline of 0.006 radians when the engine cuts out. How…

A:

Q: Note: (1) n is the student's number in the class. (2) All dimensions are in cm. (3) Dimensions need…

A: An Engineering drawing is a technical drawing.It purpose is to give information of the product for…

Q: Is this definitely correct? A few calculators online such as BMEP calculators give me a different…

A: Given data:Torque = T = 100 NmEngine is four stroke,so there is one power stroke after two…

Q: The result that I got after solving it was 463.0721, is that correct?

A: Given: d= 0.27in τ capacity=26.5 ksi = 26500 psi. Factor of safety =1.6 To find: The maximum T-force…

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: A motorcyclist left from his work at 5:45 in the morning and arrived at the coffee shop 42 km away…

A:

Q: axis of the solid. Draw its projections, sectional front view & true shape of the section. Also…

A:

Q: Indicate whether the terms are like or unlike. - 322, 5z? ... The two terms 5z and - 3z are

A: The two terms 5z2 and -3z2 are like terms.

Q: Can you pls slove this question briefly with hand written notes and diagram

A:

Q: For questions 4)r Calculate the velocity of Block B, after collision. can tutor use m1u1 + m2u2 =…

A:

Q: Draw isometric view of casting, two views (FV and SV) of which are shown in figure in First angle…

A: Given question: Draw isometric view of casting, two views (FV and SV) of which are shown in figure…

Q: Q1/b/ * Q1/b): If at location B the car move at constant velocity.. So the angle a equal to: * 30…

A:

Q: To help workers in your project site move dozens of equipment weighing 70 kgs to a height of 2.2m,…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.