For the beam shown, calculate the maximum tensile bending stress (in psi) if P = 2088 lb, Q = 8044 lb, w = 0.95 in, L = 7.94 in, b = 3.91 in, and h = 1.05 in. Round off the final answer to two decimal places. P Q P L B D E F 2 ft ←3 ft——3 ft— 2ft — -3 16+T h

For the beam shown, calculate the maximum tensile bending stress (in psi) if P = 2088 lb, Q = 8044 lb, w = 0.95 in, L = 7.94 in, b = 3.91 in, and h = 1.05 in. Round off the final answer to two decimal places. P Q P L B D E F 2 ft ←3 ft——3 ft— 2ft — -3 16+T h

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam shown, calculate the magnitude of the bending stress (in psi) at a point 1.1 in from the top of the beam on section 2.35 feet to the right of B if P = 1089 lb, Q = 4249 lb, w = 0.54 in, L = 7.82 in, b = 3.87 in, and h = 1.41 in. Round off the final answer to two decimal places. ... P W D E L B 2 ft3ft- -3 ft- 2 ft F + h
3. An A36 Steel Cantilever Beam is shown below, also showing its cross section. Determine the following: Given the formula of the Maximum allowable bending stress of steel, fb = 0.66Fy. Where Fy is the Yield Stress of Steel. Where the bending stress for a beam is (fb) = Mc/I, where c is the distance of the centroid to the extreme most fiber of the beam (either top-most or bottom-most distance). Does the Steel fail under the loading given? Use Fy = 450 Mpa. Use the Moment in (a) and the moment of inertia in (c).
Q1: The beam shown in Figure 1 is subjected to a vertical force Pv and a horizontal force Ph. The data for Pv, Ph, a,L,and e are shown in Table 1. Determine the maximum compressive and tensile stresses under the vertical force (at a distance a from the left support.) Pv = 80k N a = G0o 6 omm e %3D 26 K N 120 mm L =3600 mm Figure 1 250 mm
AW410 x 60 standard steel shape is used to support the loads shown on the beam in the figure. Assume P = 130 kN, w = 27 kN/m, a = 2.8 m, and b = 2.0m. Determine the magnitude and location of the maximum bending stress in the beam. A max = x = a i i B a → Pin |C * b W MPa m D a E
Assignment Problem 10.1. A steel bar of diameter d = 52 mm is twisted by torques at the ends. The allowable shear stress is 65 MPa. What is the maximum torque that can be applied?
Calculate the moment of Resistance of the given beams. If the maximum stress is 100 N/mm2. 190 |不 15 (i) 550 k10> (all dimensions in mm)
A rigid bar XYZ as shown in the figure below is hinged at X and is supported at Y. If the stress in the steel rod is limited to 150 ksi, determine the largest possible load P that can be applied at point Z.
A simply supported wood beam is reinforced with a steel plate of width b as shown in the figure. The beam carries a uniformly distributed load including the weight of the beam) of intensity 273 lb/ft over its 18-ft span. Using b = 4 in. and Est/Ewd = 20, determine the maximum bending stress (in psi) in the steel. Round off the final answer to two decimal places. - 6 in. - 10 in. 1/2 in. -b-
Solve the following problems completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Input your answer in the text box provided in each number. Calculate the stress in the steel of the section in PART B in MPa.0
How would you use the Central Limit Theorem in Civil Engineering? How would you use t-tests in Civil Engineering?
Calculate the design moment strength Mu for the following section. Take f'c = 40 MPa. Sketch the strain and stress distribution diagrams for each section and try to work out your solutions using equilibrium conditions. Yield stress for N bars is 500 MPa. 75 700 60 1500 T 4N28 450
Situation 2: A steel rod is inserted into a wooden block as shown. Further, two cables (one on each end) are attached to the rod where it carries a bar with negligible weight. Determine the maximum allowable force P in Newtons based on the stress and strain parameters given below. Wooden Block: Shear strength capacity = 10 MPa Bearing strength capacity = 15 MPa Normal strength capacity = 40 MPa Steel Rod: Shear strength capacity = 15 MPa 40 mm 2500 mm 100 mm 120 mm 'I 220 mm 12 mm dia.