For the beam in the figure below, determine a) the required tension in cable BC if the resultant of the three forces exerted at Point B is to be horizontal, (b) the corresponding magnitude of the resultant. Given: a = 252 in, b = 240 in, F1 = 600 N, F2 = 910 N %3D Final answer should be rounded off to 3 significant figures. a b 13 5. 54 12 3. F2 F1

For the beam in the figure below, determine a) the required tension in cable BC if the resultant of the three forces exerted at Point B is to be horizontal, (b) the corresponding magnitude of the resultant. Given: a = 252 in, b = 240 in, F1 = 600 N, F2 = 910 N %3D Final answer should be rounded off to 3 significant figures. a b 13 5. 54 12 3. F2 F1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: b) The steel Cable AB and AC are attached to the top of the transmission tower. The tension force in…

Q: Q.4) A moment and four forces are applied to a two-dimensional frame as shown in figure below.…

A: The given truss is as shown below,…

Q: The cable AB supports three vertical loads as shown in next figure. Compute the resultant of these…

Q: Q1.) A cable system is subjected to three concentrated loads as shown. The sag at point D is…

A: To Find:The sags and .The section of cable supports the largest tension and the magnitude.Given:A…

Q: 5. A person pulls on a rope with a force of 100 lbs as shown below. What is the moment about point A…

Q: 11. A truss is loaded as shown in the figure. Determine the following:a) Vertical component of the…

Q: Please give me the solution in detailed way.

Q: Variable F₁ d₁ d₂2 Values for the figure are given in the following table. Note the figure may not…

A: The beam is supported by rods AB and CD that have different cross-sectional areas. The area of rod…

Q: Q1.) A cable system is subjected to three concentrated loads as shown. The sag at point Cis measured…

A: A cable system is subjected to three concentrated loads as shown. F1 =10 KNF2 = 10 KNF3 = 30 KN The…

Q: 10 kN 4 Smart 3 soi non 12 kN 8 kN 6 kN Aqu.21 Azn Iml F

A: Given

Q: 3) Find the forces developed in beams FE, CE, and CD. State whether they're in tension or…

Q: A transmission tower (a truss) for supporting electric wires is shown. The load of wire at D is…

Concept explainers

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.

Question

For the beam in the figure below, determine
(a) the required tension in cable BC if the resultant of the three forces exerted
at Point B is to be horizontal,
(b) the corresponding magnitude of the resultant.
Given: a =
252 in, b = 240 in, F1 = 600 N, F2 = 910 N
Final answer should be rounded off to 3 significant figures.
a
13
4.
12
3.
F2
F1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2: Solution

VIEW

Step 3: Answer

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

3) A machine weighing 1500 N is supported by two chains attached to some point on the machine. One of these ropes goes to the eye bolts in the wall and is inclined 30°to the horizontal and other goes to the hook in ceiling and is inclined at 45°to the horizontal. Find the tensions in the two chains.
Q3: Three forces are acting on a steel plate with 4m length by 4m width shown in figure. These three forces are required to cause a horizontal resultant acting through point A. If F = 504N, 1) The value of horizontal resultant R is: E A D 853.814N + O 796.894N → O 711.512N - O 640.361N → O None of these
4) A ring fastened to a beam has two ropes attached. These two ropes exert forces on the ring. F₁ is applied at an angle of 20° from vertical. F₂ is applied at an angle of 0° from vertical. It is desired that the combined force on the ring is 1000N straight down. If 8° = 30°, then what are the forces, F₁ and F₂, in each rope? F2 0 8-300 20° F₁
As shown below, a sign weighing 121 N is hanging (via a wire) from a uniform 256 N beam of length L. Additionally, the beam is attached to a cable that makes an angle 0 (0 = 51°) with the beam. 0.9 L 0.7 L 501 OAK 8 X Determine the tension in the cable and the magnitude & direction of the force the hinge (the orange circle) exerts on the beam. Cable tension = Hinge force = Direction of hinge force = in quadrant - Choose quadrant - 21 CHER ° relative to the horizontal MacBook Pro kg ro from n. The o the ce tv
Q7. Determine the resultant force and angle of the forces as shown in figure by (components method the x-horizontal component and y-vertical components)? F2= 80 N 20 F = 150 N 30° 15° F=100 N F=110 N
W=200# word by zonil risdi vino 2.11 A laborer is hoisting a weight, W = 200#, by pulling on a rope as shown. Determine the force F required to hold the weight in the position shown if the resultant of F and W acts along the axis of the boom. 20 2X51290104 29buliogom silint 808 30 q12
a) As shown in the image given, a 69-kg crate is supported at equilibrium. The angles alpha=112 degrees. beta=145 degrees and the V =64.3 degrees. The coordinates of point D are (-2.2, 5.6, 3.2)m, and the spring constant k=1170N/m. Determine the stretch in the spring, in m which must be rounded to 3 places after the decimal point. Take g=9.81m/s^2. b) As shown in the image given, a 63-kg crate is supported at equilibrium. The angles alpha=112 degrees. beta=145 degrees and the V =64.3 degrees. The coordinates of point D are (-2.4, 5.5, 3.7)m. Determine the tension force in cable AC, in N. Take g=9.81m/s^2. c) As shown in the image given, a 64-kg crate is supported at equilibrium. The angles alpha=112 degrees. beta=145 degrees and the V =64.3 degrees. The coordinates of point D are (-2.2, 5.4, 3.2)m. Determine the tension force in cable AD, in N. Take g=9.81m/s^2.
Please give a detailed solution. No gpt please.
A oil rig tower is held in equilibrium by three ropes. The tension in cable AD is tightened until it reaches 4700 N. Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value d₁ 5 m d₂ 11 m 13.5 m 27.5 m 5m 65 m D d3 d4 d5 de a. Determine the magnitude of the force/tension in cord AB, TAB. b. Determine the magnitude of the force/tension in cord AC, TAC. c. Determine the magnitude of the force developed along the tower, FAE. → i. Hint: FAE = (0 +03+ FAEK) N. Round your final answers to 3 significant digits/figures. The magnitude of the force/tension in cord TAB is N The magnitude of the force/tension in cord TAC is N The magnitude of the force developed along the tower FAE is N