For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at C (positive if counterclockwise and negative if clockwise). (b) the deflection of the beam at C. Assume LAB = 310 mm, LBc = 200 mm, LCD = 150 mm, LDE = 370 mm, Mg = 210 N-m, P = 1060 N and a constant value of El = 480 x 106 N- mm² for the beam. P MB X Answers: (a) c = (b) vc= LAB B LBC C LCD D rad mm LDE E

For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at C (positive if counterclockwise and negative if clockwise). (b) the deflection of the beam at C. Assume LAB = 310 mm, LBc = 200 mm, LCD = 150 mm, LDE = 370 mm, Mg = 210 N-m, P = 1060 N and a constant value of El = 480 x 106 N- mm² for the beam. P MB X Answers: (a) c = (b) vc= LAB B LBC C LCD D rad mm LDE E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at C…

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

Q: ontinuity functions to compute punterclockwise and negative if clockwise). = 130 mm, LDE = 350 mm,…

Q: ding shown, use discontinuity functions to compute cam at C (positive if counterclockwise and…

Q: b) points late the deflections suffered by the shaft at C and D using Castigliano's Theorem. D C A B

A: Consider above figure for solution - Data given- section DC diameter D = 40.8 mm section AD and…

Q: (a) the slope of the beam at C (positive if counterclockwise and negative if o (b) the deflection of…

Q: Determine the vertical deflection at B

Q: A Determine the maximum deflection beam shown. Use Double Integration method SOKN 90kw Lam 3 ☆ gm D

A: Given Length of beam = 24 m

Q: (a) Compute the horizontal deflection at D and the vertical deflection at F by the virtual work…

Q: ne LAB = 260 mm, LBc = 190 mm, LCD = 150 mm, LDE = 350 mm, Mg = 12 for the beam. MB |B C D E LAB LBC…

Q: Use Any between AMM and CBM to determine the slopes and deflections at point D of the beam shown.…

Q: r the cantilever steel beam [E = 220 GPa; I = 102 x 106 mm*), use the double-integration method to…

Q: The overhang beam shown below has a non-prismatic section. Given E = 29000 ksi, I = 3000 in¹.…

A: Given: A non prismatic overhang beam Required: Rotation at C and deflection at D using conjugate…

Q: MB

Q: IV- Double Integration Method 4. Determine the slope and deflection at B and the maximum deflection…

Q: The beam shown has a rectangular cross section of 150mm x 200mm and is made of a material with a…

Q: of the beam at C (positive if counterclockwise and negative if clockwise). ction of the beam at C. –…

Q: 1. The beam with, cross-section shown, is subjected to the load shown. Using E-200 GPa, determine…

Q: Find the deflection at b, c and d for the loaded beam shown in the figure below by using finite…

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

Q: For the beam and loading shown, using the double integration method, determine the deflection at B…

Q: A beam shown in Figure 2 is subjected to a point load of P kN at point B and a concentrated moment…

A: Solution;

Q: (a) the slope of the beam at C (positive if counterclockwise and negative if clockwise). (b) the…

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

Q: 3) Compute the vertical and horizontal deflections of B by the virtual work method. Given E=200GPa…

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

A: Given simply supported beam with point load and couple acting. It is asked to find the 1. Slope…

Q: For the beam and loading shown, us (a) the slope of the beam at C (positi (b) the deflection of the…

A: Given:- LAB=260 mmLBC=170 mmLCD=130 mmLDE=310 mmMB=360 N-mP=1300 NEI=440×106 N-mm2

Q: 220 mm, LBc= 150 mm, LCD= 110 mm, LDE = 270 mm, eam. P MB B |D E LBC LDE B rad

Q: p, thank you.

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

Q: Problem: Determine the midspan deflection, and if the deflection max is limited to 6 mm, find Ely =…

A: Introduction- The tangent traced to the elasticity curve at the moment of maximum deflection in…

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

A: Given data LAB = 170 mm, LBC = 120 mm, LCD = 100 mm, LDE = 220 mm, MB = 230 N-m, P = 1600 N and a…

Q: For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at…

Q: See the other picture for type of loading.

Q: P10.045 For the beam and loading shown, use discontinuity func (a) the slope A of the beam at A and…

Q: Using the virtual work method, determine the ff: (a) Vertical deflection at point D (b) Slope at the…

A: Step 1: Firstly, you need to calculate the reactions at supports A, C, and D.>>RA+RC+RD=…

Q: The beam with, cross-section shown, is subjected to the load shown. Using E=200 GPa, determine a.…

Q: Using

Q: eam and loading shown, use discontinuity functions to compute ope of the beam at C (positive if…

Q: Ax MA t A Ay 2m B 10KNIM Il 2m

A: Given Uvl acting is 10 KN/m

Q: 3 k/ft B 20 ft Determine the smallest moment of inertia I required for the beam shown so that its…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

100%

For
the beam and loading shown, use discontinuity functions to compute
(a) the slope of the beam at C (positive if counterclockwise and negative if clockwise).
(b) the deflection of the beam at C.
=
Assume LAB = 310 mm, LBc = 200 mm, LCD 150 mm, LDE = 370 mm, Mg = 210 N-m, P = 1060 N and a constant value of El = 480 x 106 N-
mm² for the beam.
P
MB
X
Answers:
(a) c =
(b) vc=
LAB
B
LBC
C
LCD
D
rad
mm
LDE
E

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Do not give answer in image and hand writing
For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at C (positive if counterclockwise and negative if clockwise). (b) the deflection of the beam at C. Assume LAB = 180 mm, Lgc = 120 mm, LcD = 100 mm, LDE = 220 mm, Mg = 210 N-m, P= 1300 N and a constant value of El = 630 × 10° N- mm? for the beam. MB B \C |D E LAB LBC LcD Lpe Answers: rad (a) ec = m (b) vc=
= In the figure shown, each of the four vertical links connecting the two rigid horizontal members is made of aluminum (E 70 GPa) and has a uniform rectangular cross section of 10 x 40 mm. For the loading shown, determine the deflection and the direction of (a) point E, (b) point F, (c) point G? 250 mm 400 mm 250 mm B 40 mm. E 300 mm 24 kN
For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at C (positive if counterclockwise and negative if clockwise). (b) the deflection of the beam at C. Assume LAB = 190 mm, LBC = 130 mm, LCD = 100 mm, LDE = 240 mm, Mg = 190 N-m, P = 1310 N and a constant value of El = 480 × 106 N- mm2 for the beam. MB |C D E LAB LBC LCD LDE Answers: (а) Ос — rad (b) vc= mm
For the beam and loading shown, use discontinuity functions to compute(a) the slope of the beam at C (positive if counterclockwise and negative if clockwise).(b) the deflection of the beam at C.Assume LAB = 270 mm, LBC = 180 mm, LCD = 150 mm, LDE = 350 mm, MB = 330 N-m, P = 1700 N and a constant value of EI = 480 × 106 N-mm2 for the beam.
Please see the attached image. Thank you
Use Geometric Method. Determine the Vertical Deflection at B. Indicate the negative sign if the answer is downward
For the beam and loading shown, determine the deflection at the mid point in slope at point B in radian. The wr? %3D (L- x) wr3 equation of elastic curve are the following: EIy (3L – 4x), Ely 24 24 E = 200 GPa, I = 1660 x 10^6 mm^4 Let w = 158kN/m, L = 13m Answer in three decimal places w A В -L/2
For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at C (positive if counterclockwise and negative if clockwise). (b) the deflection of the beam at C. Assume LAB = 280 mm, LBc= 180 mm, Lcp = 140 mm, LDE = 380 mm, Mg = 280 N-m, P = 1010 N and a constant value of El = 590 × 106 N- mm² for the beam. P MB X Answers: (a) 0c = (b) Vc= LAB B -0.0133 -11.91 LBC C LCD D rad mm LDE E
fons/1679264 Use Double Integration Method to analyze the deflection of the beam shown: (IS EN 6 N/o 160 O - 3 m -Sm Determine the following: (2 decimals for non-whole numbers) (a) C1 = kN-m2 %3D (b) C2 = kN-m2 (c) Ely under the 15kN load kN-m3 (d) upward(U) or downward(D)?
For the beam shown, use the conjugate beam method to compute the vertical deflection at C. Use: E = 200 GPA IAC = 100 x 106 mm“ ICF = 50 x 106 mm4 10 kN D. E 100 kN-m te s m-t-5 m--k-5 m--ksm--k–10 m– O 41.65 mm O None of the Above O 42.65 mm O 43.65 mm O 44.65 mm
From the given figure below, determine the maximum deflection and slope of the beam. Use double Integration Method