For the beam and loading shown, determine the minimum required width b, knowing that for the grade of timber used, Oall = 12 MPa and Tall = 826 kPa - (Round the final answer to two decimal places.) 2.4 kN 4.8 kN 7.2 kN B C D 150 mm 1 m 1 m 1 m 0.5 m The minimum required width bis mm.

For the beam and loading shown, determine the minimum required width b, knowing that for the grade of timber used, Oall = 12 MPa and Tall = 826 kPa - (Round the final answer to two decimal places.) 2.4 kN 4.8 kN 7.2 kN B C D 150 mm 1 m 1 m 1 m 0.5 m The minimum required width bis mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A sawn lumber column with a 5.5 x 5.5-in. cross section has an 11-ft effective length. Knowing for…

A: For sawn lumber column,Dimension is 5.5 × 5.5-in. cross sectioneffective Length= 11-ft σC = 2050…

Q: Calculate the maximum allowable load (in kN) that a nominal 350mm x 350 mm sawn lumber column, 3.5m…

A: Solution-The given values are as follows,The column dimension=350×350The column…

Q: Determine the required reinforcement for T-section beam to resist torsion T = 11.75 KN.m with the…

A: Moment of resistance = 0.87 Ast [ d-0.42 ]moment of resistance for high yield reinforcement =…

Q: Refer to figure SD-07Q007. Given: Slab thickness 150 mm Dead load=4.8 kPa (superimposed) Live load =…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: A fully erected timber of rectangular cros- section was compressed due to an axial load resulting to…

Q: A 130 mm x 220 mm timber wood is used for the beam shown. Take E = 8.22 MPa. w = 8.65 kN/m, L =7.…

A: Given data:- W =8.65 kN/m L = 7 m E = 8.22 MPa Cross section of beam = 130 mm x 220 mm To find:-…

Q: For the beam shown, determine the tensile development length required for the epoxy coated bars if…

Q: A timber wall 50 mm wide x 50 mm deep and having a height of 3.50 m is assumed to be hinged at top…

A: The question is based on the timber wall hinged at the top and the bottom and a load is applied on…

Q: simply supported beam is reinforced with 5-25mm-diameter at the bottom and 2-20mm-diameter at the…

Q: 2. Find the following, given that the beam below is a sawn lumber beam made of Douglas-Fir 4"x Nol &…

A: Given: L = 20 ft W = 195 lbs/ft Douglas Fir properties: fy = 8093.106 psi E = 2001521 psi

Q: Determine the reinforcement required of a beam cross section shown in the Figure of ? = 400??,? =…

Q: the maximum shear stress in the wood. Vmax=3530.8 N, Iz=287239583.3 mm4 Answer: 0.2017MPa

A: Given data Vmax.=3530.8 N, Iz=287239583.3 mm4 width, b=40×2=80mm

Q: A pair of wood components having a dimension of 100mm X 100mm is joined by means of glue as shown.…

A: angle from horizontal θ=tan-134=36.86°shear stress on glued section ζ= 1650 Kpaand normal stress…

Q: Determine the Maximum Shear and Bending Stress of the Propped timber beam in the figure. The total…

A: Given, D = 264 mm L = 7.70 m

Q: L, Structural Select, sawn lumber beam? O 13.8 MPa O 16.5 MPa O 18.3 MPa O 10.0 MPa O 19.5 MPa O…

A: A timber is defined as the sawn wood that is used in the form of a structural member having the…

Q: For the beam and loading shown: (a) Draw complete shear and moment diagrams using the relations…

A: Calculate the support reactions at support A and B:…

Q: 2. Refer to Sketch #2 and assume a 250 #/SF design load on the decking (plywood) a. Determine…

A: Given data Load on plywood decking =250psf a.) The expression for linear load on 12'' wide strip of…

Q: Shown in the figure below is a sawn lumber beam made of Douglas-Fir 4"x No1 & Btr grade. Select the…

A: The given rate of loading is 210 pounds per linear foot =210 lb/ft The total load will be:…

Q: A short column is made by nailing four 1 x4-in. planks to a 4 x 4-in. timber. Using an allowable…

A: Given: A short column is made by nailing four 1 x4-in. planks to a 4 x 4-in. timber. Using an…

Q: 4. Given the following properties of T-beam Effective flange width (b).......1200 mm Width if the…

Q: Seatwork No. 1 1 whole yellow sheet of paper or bond paper A rectangular beam having a 7-m simple…

A: Given:- The span length of the beam = 7 m The superimposed dead load = 28 kN/m The live load = X =…

Q: aminated wood beam consists of eight 2.25 in. × 5.25-in. planks glued together to form a section b =…

A: Maximum shear force is τmax≥VmaxQItQ=5.25×9×92I=5.25×18312so,V≤1105.25×183125.255.25×9×92V=6930lb

Q: A laminated wood beam consists of eight 1.75 in. x 5.50-in. planks glued together to form a section…

A: To find out the moment of inertia about Z axis.

Q: A TIMBER BLOCK “400 x 400” mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A “400” mm AND ‘t’ mm THICK…

A: Given:- Axial load=1000 kNMaximum timber stress=12 MPaMaximum stress in steel=350 MPaModulus of…

Q: Pls help. A laminated wood beam consists of eight 2 in. × 7.00-in. planks glued together to form a…

Q: 5. Given : Allowable bending stress of 12.5 MPa Allowable shearing stress of 0.45 Mpa Elasticity of…

Q: Calculate the maximum allowable load (in kN) that a nominal 300mm x 300 mm sawn lumber column, 3.0m…

A: Given:- Cross section of column 300mmX300mm Length of column L=3m…

Q: Find the magnitude of the concentrated load P (in lbs). If P = 25,000 lbs, find is the maximum shear…

A: given- A simply supported wooden beam with a span of 16 ft supports a concentrated load P at the…

Q: A reinforced concrete one-way slab is built integrally with its supporting beams which are all 12…

Q: Problem 6.3 A short column is made by nailing four 1 x 4-in. planks to a 4x4-in. timber. Using an…

A: Given data : Allowable stress = 600 psi To Find : Determine the largest load P that can be applied…

Q: If the allowable shear strength of the wood is 80 psi, determine the maximum load P that may be…

A: Allowable strength of beam (σ) = 80psi Moment of inertia (I) = bd3/12 = 6x103/12 = 500 in4 Distance…

Q: Determine the required reinforcement for T- section beam to resist torsion T = 11.75 KN.m with the…

A: Moment of resistance = 0.87 fy Ast [ d-0.42 xu] moment of resistance for high yield reinforcement =…

Q: Assignment 1: On a red pine lumber beam with span of 3.2 m, the standard value of the permanent…

A: Section modulus is a geometric property for a given cross-section used in the design of beams and…

Q: A timber post of Douglas fir is subjected to an axial compressive load of 60,000 lb. The nominal…

A: Find out Stress due to compressionCompressive Stress=LoadAreaAreafrom table for…

Q: Calculate the maximum allowable load (in kN) that a nominal 350mm x 350 mm sawn lumber column, 3.5m…

Q: A laminated beam is composed of five planks, each 6 in. by 2 in., glued together to form a section 6…

A: Given : Plank size - 6 in. by 2 in. Allowable shear stress in glue = 90 psi Allowable shear stress…

Q: It is desired to remove the spike from the timber by applying force along its horizontal axis. An…

Q: Explain briefly the strength of the timber and how to determine these strengths in laboratory?…

A: As when the density rises, the strength of timber improves. The degree of humidity where its mass…

Q: 8. For a section 6 inches wide and 14 inches deep, and a cover of 2 inches, what is the maximum safe…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

For the beam and loading shown, determine the minimum required width b, knowing that for the grade of timber used,
Oall = 12 MPa
and
Tall = 826 kPa
- (Round the final answer to two decimal places.)
2.4 kN
4.8 kN
7.2 kN
B
C
D
150 mm
1 m
1 m
1 m
0.5 m
The minimum required width bis
mm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Minimum of 3 decimal places in all computations.
A TIMBER BLOCK “B x B” mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A “B” mm AND ‘t’ mm THICK STEEL PLATES. DETERMINE THE THICKNESS ‘t’ SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY.
#2 will upvote anyone who will answer correctly. Thanks
EX:Design the shear reinforcement for the beam shown below, w, =2002 £, = 27.6Mpa. f, = 414Mpa, use 010mm stirrups. w, =200 b= 300mm = soofum| en Note, the solution must be ASCE 7-10 Specifications.
Design a singly reinforced beam. Use f'c = 28 MPa, fy = 414 MPa
A laminated beam is composed of four (4) planks, each of 150 mm x 30 mm, glued together to form a section 150 mm x 150 mm. The allowable shear stress in the glue is 850 kPa, the allowable shear stress in the wood is 1050 KPA, and the allowable flexure stress in the wood is 10 MPa. Determine the maximum uniformly distributed load which can be carried by the beam on a 45 m simple span.
using the table below, answer the question
1. For the beams described below, determine the nominal capacity oMn Assume f'c = 4ksi fy = 60ksi Clear cover = 2 inches a) 3 No 6 Pmin=0.0033 Pmax=0.01806 b = 8in h=20in b) b=5in h=16in 4 No 3