For the beam and loading shown, design the cross section of the beam, knowing that the grade of timber used has an allowable normal stress of 11.5 MPa. (Round the final answer to one decimal place.)

Q: Write the formula for the time required to fill the cavity by the bottom gating system.

A: Given: Bottom gating system

Q: 00 0 021 0 043 0 25 0 1280

A:

Q: A 1 Cutting Fluids 2 HSS 3 Serrated or segmented chips 4 Vertical shaper 5 Milling B Chip load 7…

A:

Q: Impact velocity equation

A:

Q: %o change in diamefesx-?

A: Given; Solid cylinder of; diameter,d1=120 mmheight,h1=50 mmTwo frictionless flat dies to a…

Q: Determine the y_bar coordinate of the composite shape. Treat the bent corners as square and ignore…

A:

Q: Successive approximation ADC explian

A:

Q: State the difference between the eutectic and eutectoid points.

A: Eutectic point: In the iron carbon phase diagram at 2 percentage of carbon is called eutectic point.…

Q: Figure shows a heat exchanger designed to cool 5250 kg/h of an ethyl alcohol solution (Cp = 3810…

A:

Q: Differentiate between single acting and double acting cylinders.

A: Differentiate between Single Acting & Double Acting Cylinder :

Q: Determine the distance and resultant of the five parallel forces acting on the rocker arm of the…

A:

Q: In a workshop, Drilling operator is working on a Drilling machine. The drilling operator needs to…

A:

Q: dy 35+メ9

A: The provided differential equation is given as, dydx=3y2+xyx2

Q: Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each…

A: Consider a vehicle engine where number of cylinder are situated whose bore diameter is D and stroke…

Q: Q/ The force in the member (CA) is 12m 50 ку. 10 points 5m 16x

A:

Q: Which of the following statement is correct O 1. Reynolds number depends on the viscosity of fluid O…

A:

Q: The column consists of a wooden post and a concrete footing, separated by a steel bearing plate.…

A: Given data: The working stress for wood is σWood=1100 psi The working stress for concrete is…

Q: The coefficient of bend value in the energy loss due to bend in a pipe depends on the pipe diameter,…

A: Coefficient of bend value depends on ?

Q: The Taylor's tool life component is 0.3 and constant is 120 for a cutting tool A and 0.5 and 30 for…

A: Given:nA=0.3CA=120nB=0.5CB=30

Q: Place the labels with the most accurate description on the micrograph at locations A, B, and C, as…

A: given; Place the labels with the most accurate description on the micrograph at locations A, B, and…

Q: P? P G P

A:

Q: 181-2,4,0)m A0, 0-6) m Dl0,0, -3 )m w •10 KN ト

A: From the free body diagram given, write the tensions in the cables in cartesian vector form by using…

Q: tan30*sin30

A: Given, Value of tan30 and sin30 is, tan30°=0.577sin30°=0.5

Q: Refer to drawing 21A035, what is the depth of the spotface?

A: Spotface: A spotface is an accurate round surface on a machined part providing proper seating of a…

Q: Draw the three views and a section elevation:

A: The three views and Sectional Elevation views are drawn with the scale 1:1.

Q: -d12 The figure shows a tabletop experi- nent that can be used to determine an unknown homent of…

A:

Q: Whats the formulae for temperature error %

A:

Q: Customary units by using the values listed for length and mass as defined values: Bending moment or…

A: As moment bending moment or torque has two variables, force and distance. So, M = F × r…… (1) The SI…

Q: When does a couple of moment work?

A: A couple is when a system of forces has no net force but has a net moment. A couple causes pure…

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A:

Q: Y 8 12 8 12 R= 3

A:

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: 2 Brass expands more than iron when heated. How would the strip look after prolonged exposure to…

A:

Q: Q// Drow the 5.8.0 and B,m.D yougN

A: The shear force diagram for the beam is

Q: 13378.2898 lbm to lbf

A:

Q: Indicate whether the terms are like or unlike. - 322, 5z? ... The two terms 5z and - 3z are

A: The two terms 5z2 and -3z2 are like terms.

Q: During the governor regular working time the sleeve moves up with 16mm due to the effort of 225N…

A: Given that, The effort of the governer, F=225 N and the movement of the sleeve is, x=16 mm=0.016 m,

Q: name these lines

A: The names of the given lines is given below.

Q: What does the shear flow measure?

A: The shear flow is defined as the shear force per unit length in a thin walled perimeter. The…

Q: 4. The weight of the box is W = 90 N and the coefficient of static friction between the box and the…

A:

Q: 12 Find maX. W=? if of530Mpa Ś GoMpa い Joomm 2m An 30 そaん 500

A: Stress When body is subjected to any load then body resist that load and the resistance is called as…

Q: Round number to three significant figures. 0.000045389

A: Given data: The given number is N = 0.000045389. Here, there are a total of 5 significant figures.…

Q: CHI) plane Cho use your knowledge of Geometry and the Vale a = (7-92 X1000) cm to determine the Sur…

A: There are three half spheres and three 60 degree angle spheresIt is asked to find the surface…

Q: Deleimine wasik done

A: Given data : The value of force applied=F The value of displacement=D   To find : Work done