For the amplifier circuit shown 1. hie = + ohm 2. Av = Vo/Vs = %3D 3. Zi = ohm 4. Zo = + ohm +9V Zi 100KO Zo B = 50 1µF Vo(t) Vs(t) 1ΚΩ 1KO

Q: 0 U7 IONI M 의 E U1:B ** 0 UI:D aret 00 UB:A Hi D2 LED-BLUE 7° A= 3 U4 LU LESTE 10 노 3888888 ARUBEND…

A: 7 seven Proteus Anode Displays Available in Proteus - => Proteus contain all the segment display…

Q: The error for an ammeter is found as ±2%, the true range of the current it can give for 10 mA is

A: Given: The error for an ammeter, error=±2% Current, I=10 mA

Q: In STEP 4, you charged the capacitor completely with the PSB set to 3.3V. Then you set the PSB to 5V…

A: Given Initially capacitor charged to 3.3v with PSB set to 3.3v After sometime PSB is set to 5v then…

Q: A proton is heavier than an electron by ------ times.

A: Protons are positively charged particles and they reside inside the atomic nucleus. The electrons,…

Q: 1: Theory 1.1 Describe briefly a sinusoidal signal and ALL its properties. Give example with…

A:

Q: What is the difference between 5g and periouvse generations

A: There are various difference between 4G and 5G.

Q: Sketch v, for the network of the figure below for the input shown. Show the details of your work.

A:

Q: - 8V R₁ = 1.2 k s m flav R2=2.5K2 O R3=5602 Analyze the circuit using any circuit analysis method to…

A:

Q: How many 40 W cool white fluorescent lamps would be required to have an initial lamp output of 9,600…

A: Given:Power. P=40WOutput=9600 lumens

Q: If the ammeter parameters due to insertion include 1200 internal resistance and a load resistance of…

A: Given, Internal resistance, Rint=120 Ω Load resistance, RL=2 kΩ Let the source voltage is V

Q: When we add impurities such as phosphorus to a pure semiconductor (silicon), * ------the number of…

A: When we add impurities such as phosphorous to a pure semiconductor (silicon), they form n-type…

Q: What special type of diode is used in the circuit? Given the state of the switch as shown, what is…

A:

Q: Without changing the locations of the loads in the figure, a) Draw a suitable diagram to measure the…

A:

Q: 1.5L 1-5A 1.55L Reg = ?? %3D

A:

Q: In a 110 punch down block each plastic space joins two wires together then insert a connecting block…

A: A 110 punch down block is used for the termination of a cable,not for for connection of two wire.

Q: what is the power disipated by R1

A:

Q: Table 3 6. Plot the values from Table 2 and Table 3 on the same graph done in step 3. Does the diode…

A: Diode is device which is made of semiconductor, basically it act as switch

Q: For given circuit and input voltage, draw the output response of circuit . I sent you questions…

A: For given circuit and input voltage, draw the output response of circuit . I sent you questions…

Q: The condition at which a FE

A:

Q: Q) A galvanometer is used as a O Current source. O Voltage source. Null detector. Input resistance

A: Galvonometer is a measuring device give deflection when current flows through it.

Q: Write the conclusion of full subtractor?

A:

Q: What is the approximate current level in the gate of an FET in dc analysis? undefined 00 O 0.3mA O…

A:

Q: One of the following elements can be used to make P-type semico Phosphor(P) Arsenic(As) Antimony(Sb)…

A: For p-type materials we need elements having three valence electrons.

Q: Convert 628 to binary

A: Given(62)8

Q: Can you help me with this homework problem? Constant voltage drop is Vd=0.7 What is the output volts…

A: The circuit diagram,

Q: Convert following number in the given radix system. (a) (1010.011)2 to (…………)10 (b) (0.513)10 to…

A: a) Convert base-2 to base-10 To convert base-2 to base-10, multiply with their weights.…

Q: hat should I do when I get a current like 0.263187845A, should I round into the simplest form, or…

A: Give a current value and asked to rewrite it in different forms.

Q: does TP4056 can prevent 3.7v li-ion battery from overcharging? What is the maximum voltage of the…

A: Given  We need to determine whether  TP4056 can prevent 3.7v li-ion battery from overcharging and…

Q: Determine the voltage and current meter indications in each circuit.

A:

Q: If the average of set of voltage reading is 55.3V. The precision for one of the reading 51.8 will be…

A: Given Data: Yn = 55.3 Xn = 51.8

Q: c) Strain gauge is one of the resistive transducers. Determine the strain gauge resistance of a…

A: We need to find out resistance for given details

Q: Select the most commonly used semiconductor elements.   Note: it is in Spanish, but it is easy to…

A: The material which have 4 valence electrons in outer cell are known as semiconductor material.

Q: reading is due to the a. insertion O b. loading effect с. c. battery aging d. O d. conversion

A: In this question we will write about loading effect....

Q: If a multiratio CT having 1505 CT ratio with 0.104 ohm secondary resistance and the excitation…

A: Given CT ratio = 150:5 secondary resistance = Zs =0.104 ohm Excitation current Ie =0.2 A I'=5 A…

Q: Ic=? VCE = ? 180 kr 20V. {.5KQ 5km Ic UCE B = 100

A:

Q: can you give an Introduction about 3 Band Equalizer, the use of it and how it works

A: We have given the problem  can you give an Introduction about 3 Band Equalizer, the use of it and…

Q: If we use 5000 µF, we can get a very low ripple voltage. But this is so bad and this a disadvantage,…

A: Ripple voltage usually occurs when we convert the AC voltage in to DC voltage conversion. But at…

Q: Instructions: Determine the indicated parameters from the given circuits and show the complete…

A:

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.