For simplified processing calculations, glass-bottle shaping temperature can be taken as the softening point (at which n = 107.6 P ), and the subsequent annealing temperaturecan be taken as the annealing point (at which n = 1013.4 P ). If the glass-bottle processing sequence involves a shaping temperature of 690 °C for a glass with an activationenergy for viscous deformation of 440 kJ/mol , calculate the appropriate annealing temperature.Express your answer to three significant digits.

The softening temperature is Ts=690°C. The activation energy is Q=440 kJ/mol. The viscosity at the…

For simplified processing calculations, glass-bottle shaping temperature can be taken as the softening point (at which 7 = 107.6 P ), and the subsequent annealing temperature can be taken as the annealing point (at which 7 = 1015.4 P ). If the glass-bottle processing sequence involves a shaping temperature of 690 °C for a glass with an activation energy for viscous deformation of 440 kJ/mol, calculate the appropriate annealing temperature.

For simplified processing calculations, glass-bottle shaping temperature can be taken as the softening point (at which 7 = 107.6 P ), and the subsequent annealing temperature can be taken as the annealing point (at which 7 = 1015.4 P ). If the glass-bottle processing sequence involves a shaping temperature of 690 °C for a glass with an activation energy for viscous deformation of 440 kJ/mol, calculate the appropriate annealing temperature.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A sample of giant reed is shaped into a beam with a square cross section of 15.5 mm by 15.5 mm. Two supports placed 22.1 mm apart support the sample and a load is applied halfway between the support points in order to test the force required to fracture the sample. If ultimate tensile strength is 912 MPa, what would be the force F (newtons) required to cause failure?
3
Ordinary sheets of borosilicate glass are tested in bending, and are found to fracture at an average stress of 72 MPa. After thermal tempering, the stress at failure increases by 90%. What are the sign and magnitude of the stress induced in the glass by the tempering operation?
GKN Sinter Metals Company pressed iron powders using a compaction pressure of 600 MPa to produced a cylindrical bearing which is 70 cm long and has internal and external diameters of 8 cm and 16 cm, respectively. Determine (a) the most appropriate pressing direction, (b) the required press tonnage to perform this operation, and (c) the final weight of the part if the porosity is 12%, given that the density of iron, ρ = 7.87 g/cm3. Assume shrinkage during sintering can be neglected
I1
As the lead engineer for a LPG storage project, you are overseeing the design of pressure vesselssuch as those shown below. Identify which test (or tests) is mostsuitable to pick a material and thickness for the spherical shell of the pressure vessel. Why these are the relevant tests. Explain what information these tests provide and why it is important to determining material and thickness.
Homogeneity of metal is developed in hot forming process. ОF От Powder metal technique is used for-- ----materials. * High melting point and hardness O High ductility O low melting point Extrusion process is used to form all the materials. O T
8.4 A Douglas-fir post has a diameter of 0.3 m and a length of 5.0 m. The initial temperature is 20°C and it is placed in a retort of creosote at 98°C. The moisture content is 12%. (a) What time is required to raise the temperature of the center to 82°C? (b) To 98°C?
The tensile strength for cold-rolled magnesium alloy AZ31B plate is approximately 160 MPa for specimens tested either parallel or perpendicular to the rolling direction. When similarly oriented specimens are compressed, the yield strength is only 90 MPa. Why? (Hint: Consider the possible deformation mechanisms available in the magnesium alloy and any crystallographic texture that might exist in the wrought plate.)
Question 2 The following data relate to an injection moulding grade of a thermoplastic polymer. Determine whether this melt obeys the power law and if so, estimate the power law exponent n. Comment on your findings. Shear rate (s') Viscosity (Pa.s) 10 2590 100 2260 500 1370 1000 845 2000 525 5000 278 10000 175
Alplas Plastics uses an extruder in which the barrel diameter = 0.4 m and length = 6.0 m. The extruder screw rotates at 65 rev/min; it has channel depth = 0.02 m and flight angle = 16°. The plastic melt has a shear viscosity = 85 Pa-s. Determine: (a) Qmax and pmax; (b) the shape factor Ks for a circular die opening in which Dd = 0.009 m and Ld = 0.03 m; and (c) the values of Q and p at the operating point
What is the advantage of nitriding? Select all correct answers. Some complex components can be nitride without difficulty. Better wear resistance. Better fatigue resistance. The cheapest method of case hardening. What is the correct definition of plastic deformation? The behavior of a material when its size changes by the addition of heat. The behavior of a material that deforms under load and returns to its original shape when the load is removed. Deformation caused by cleavage, where the material is actually pulled apart across atomic planes within the crystals or along the grain boundaries. The behavior of a material that deforms under load and does not fully return to its original shape when the load is removed.